background image

Page 3

Back

Front

Panel 1

Panel 2

Face Plate

Description

Safety Guidelines

•  Save these instructions. This manual contains important instructions that will assist you during  installation and    

   for maintenance.

•  Keep all the components secure and protected during storage.

•  Be careful of finished surfaces during transport and installation to avoid damaging the finish. 

•  Installation and maintenance should only be performed by qualified electricians.

•  It is recommended a minimum of 2 people perform installation.

•  Do not install phone during extreme weather conditions.  

•  Do not touch uninsulated phone wires or terminals unless the phone line has been disconnected at the  

   network interface.

•   ADA compliant (hands free operation)

•   LED call status indicator

•   Powder coated steel construction inside and out 

•   Aluminum access panels powder coated inside and out

•   Weather and vandal resistant

•   Blue beacon and strobe 

•   Strobe turns on upon phone activation

•   Recessed illuminated face plate

•   Internal anchor base plate

•   Ability to program up to 5 emergency numbers*

•   Remote or on-site programmable**

•   Panels secured with security screws

•   Torx bit provided to access panels

Features:

Height

9’

Width

10-3/4”

Depth

6”

Thickness of Steel

11 Gauge

Weight

167 lbs.

Tower Specifications:

*Not applicable for 2-Way Radio application

**Not applicable for 2-Way Radio, Cellular, or 

   900 MHz application

Tower Site Preparation Instructions

1.

 Concrete mounting pad should be at least 16” in depth and 2’ in diameter.

2.

 Insert the 3/4” x 12” galvanized rods per mounting template provided.

3.

 A minimum 2” of thread must be exposed above level of concrete.

4.

 Let concrete set for a minimum of 48 hours to cure.

Figure 1: Front & Back View

Summary of Contents for 2100-TL9










Reviews: