background image

P

19

WARNING

Failure to replace a faulty hose, secure gas supply connections or to open the Lids before
proceeding to the Lighting Procedures could result in a fire or explosion could result in a fire
or explosion that could cause serious bodily injury, death, or property damage.

Manually Lighting Your Grill By Paper Match

To light your gas grill by match, insert a match
into the Lighting Stick and follow steps 1
through 7 of the Grill Lighting Instructions. Then,
light the match and place Lighting Stick through
the Cooking Grid on the grill as shown below.
Turn the Control Knob nearest the open tank to
the HIGH setting to release gas. The Burner
should light immediately.

WARNING

Never lean over the grill cooking area while lighting your gas grill. Keep your face and body a
safe distance (at least 18 inches) from the Lighting Hole or Burners when lighting your grill by
match.

Use and Care Instructions

To purge air from your gas line and/or reset the regulator excess gas flow device:

Turn Control Knobs to the OFF position.
Turn off the gas at the tank valve.
Disconnect regulator from LP Gas tank.
Let unit stand 5 minutes to allow air to purge.
Reconnect regulator to the LP gas tank.
Open the Grill Lids.
Turn tank valve on SLOWLY 1/4 of a turn.
Push and turn the middle Control Knob farthest from open tank to HIGH.
Press Electric Igniter for 3-4 seconds to light the burners.

WARNING

Should a FLASHBACK fire occur in or around the Burner Tubes, follow the instructions below.
Failure to comply with these instructions could result in a fire or explosion that could cause
serious bodily injury, death, or property damage.

Shut off gas supply to the gas grill.
Turn the Control Knobs to OFF position.
Open the Grill Lids.
Put out any flame with a Class B fire extinguisher.
Once the grill has cooled down, clean the Burner Tubes and Burner according to the
cleaning instructions in this Operator’s Manual.

!

!

!

!

!

!

Summary of Contents for ST1017-012939

























Reviews: