background image

OPERATOR MANUAL

IMPORTANT INFORMATION, KEEP FOR OPERATOR

2016 Gees Mill Road, Suite 200, Conyers, GA 30013

888-994-7636,  fax 888-864-7636

unifiedbrands.net

PART NUMBER PP MNL2103, REV. A (06/21)

This manual provides information for:

RCS-24-WS 

24” CHEESER STATION™ 

WITH INTEGRAL SCALE 

(SHOWN)

RCS-24 

24” CHEESER STATION™

THIS MANUAL MUST BE RETAINED FOR FUTURE REFERENCE.  READ, 
UNDERSTAND AND FOLLOW THE INSTRUCTIONS AND WARNINGS 
CONTAINED IN THIS MANUAL.

FOR YOUR SAFETY

 Do not store or use gasoline or other flammable vapors 

and liquids in the vicinity of this or any other appliance.

WARNING

 

R290 flammable refrigerant in use. 

Improper installation, 

adjustment, alteration, service or maintenance can cause property 
damage, injury or death.  Read the installation, operating and maintenance 
instructions thoroughly before installing or servicing this equipment.

NOTIFY CARRIER OF DAMAGE AT ONCE

  It is the responsibility of the 

consignee to inspect the container upon receipt of same and to determine 
the possibility of any damage, including concealed damage. Unified 
Brands suggests that if you are suspicious of damage to make a notation 
on the delivery receipt. It will be the responsibility of the consignee to file 
a claim with the carrier. We recommend that you do so at once.

Manufacture Service/Questions 888-994-7636.

RETAIN THIS MANUAL FOR FUTURE REFERENCE

 

NOTICE: Due to a continuous program of product improvement, Unified Brands  
reserves the right to make changes in design and specifications without prior notice.
NOTICE: Please read the entire manual carefully before installation.  If certain 
recommended procedures are not followed, warranty claims will be denied.

MODEL NUMBER _________________________

SERIAL NUMBER _________________________

INSTALLATION DATE ______________________
The serial number is located on the right side inside 
the base cabinet behind the grilled hinged door. An 
example is shown here.

EQUIPMENT DESCRIPTION

Information contained in this document is known to be current and accurate at the time of printing/creation.  Unified Brands 

recommends referencing our product line websites, unifiedbrands.net, for the most updated product information and 

specifications. The company reserves the right of final interpretation of the user manual. Information subject to change without 

notice. © 2021 Unified Brands. All Rights Reserved.  Unified Brands is a wholly-owned subsidiary of Dover Corporation.

MODEL

LENGTH

DEPTH*

HEIGHT

INTEGRATED 

SCALE

CHEESE BIN 

STORAGE CU. FT.

HP

VOLT/CYCLE/

PHASE

AMPS

NEMA 

PLUG

SHIP WT.

WORK SURFACE

REAR OF UNIT

RCS-24-WS

24”

33”

36”

41”

YES

1.25

1/4

115/60/1

1.8

5-15P

180

RCS-24

24”

33”

36”

41”

NO

1.25

1/4

115/60/1

1.8

5-15P

180

*Depth = 34” with 1” standoff bumpers

RCS-24-WS

RCS-24

Summary of Contents for RCS-24


















Reviews: