Raleigh Audio Standard Extreme RAKK dac Mark III Assembly Manual Download | Manualshive

Page: 54 / 65

background image

Position the Front panel

1.

Tighten the KEP nut in the middle of front panel while lifting the front panel so it
contacts the tops of the mounting holes. This ensures that it's straight with respect to the
shelf it will be sitting on.

2.

Secure the front panel to the side panels with four 8-32 KEP nuts. Snug up these four
nuts.

Now with all of the screws and nuts snug, a side panel can be moved with some force, if need be.

Position the top panel

1.

Place the top panel on the top of the unit and check that the holes in the top panel are
centered over the screw holes in the side panels and back panel.

2.

Adjust the side panel alignment at the front by moving the top of the side panel left or
right as is necessary to make the holes in the top panel align properly with the holes in the
side panels.

Secure the back, side and bottom panels

1.

Install nine screws in the top panel. Firmly tighten these screws.

2.

Firmly tighten the four screws securing the back panel to the side panels.

3.

Firmly tighten the three screws securing each side panel to the bottom panel.

4.

All screws should now be firmly tightened.

Secure the front panel

1.

Remove the top panel.

2.

Firmly tighten the four KEP nuts that are securing the front panel to the side panels.

3.

Place the top panel on the top of the unit and check that the holes in the top panel are still
centered over the screw holes in the side panels and back panel.

4.

Set the top panel aside for now. You will install it after the final electrical adjustments
are made.

————————————————————————————

53

«
...
52
53
54
55
56
...
»

Summary of Contents for Standard Extreme RAKK dac Mark III


































































Reviews:

No comments

Related manuals for Standard Extreme RAKK dac Mark III

Brand: XINDAK Pages: 8

Brand: La Marche Pages: 15

Brand: Barco Pages: 8

Brand: Barco Pages: 3

Brand: Barco Pages: 61

Brand: NAD Pages: 10

Brand: Parker Pages: 36

Brand: R.L.DRAKE Pages: 8

Brand: R&S Pages: 89

Brand: R&S Pages: 19

PowerRouter PR50S

Brand: Nedap Pages: 64

OmniConverter GPoE+/S

Brand: OST Pages: 10

Brand: xpr Pages: 12

Brand: Statpower Pages: 28

Interface Module XC Modbus

Brand: Baer Pages: 10

Brand: Kramer Pages: 15

Brand: PEAK COMMUNICATIONS Pages: 18

Brand: Gbxpoint Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands