Raleigh Audio Standard Extreme RAKK dac Mark III Assembly Manual Download

Page: 34 / 65

35.

Locate the 11” red/black twisted pair that is connected to the 12V DC Output.

•

It will be connected to the 12V pads on the Active Output output board.

•

Connect the red wire to the “+” pad.

•

Connect the black wire to the “-” pad.

36.

Secure the Power Supply board with five 6-32 x ¼” screws.

————————————————————————————

♪

Mount the RAKK dac

37.

Place the RAKK dac in its location next to the Active Output board.

•

Orient the board such that the Output pads are closest to the Active Output board.

•

Do not secure the board yet.

38.

Locate the orange/black twisted pair, blue/black twisted pair and black wire that are
connected to the “From RAKK dac” pads on the Active Output.

•

These will be connected to the “Output” pads on the RAKK dac.

•

Connect the orange wire to the “R+” pad and
connect the associated black wire to the “R-” pad.

•

Connect the blue wire to the “L+” pad and
connect the associated black wire to the “L-” pad.

•

Connect the black wire to the “REF” pad.

39.

Locate the 20” red/black twisted pair that is connected to the 10V Regulator DC Output.

•

It will be connected to the 12V pads on the RAKK dac.

•

Connect the red wire to the “+” pad.

•

Connect the black wire to the “-” pad.

————————————————————————————

Summary of Contents for Standard Extreme RAKK dac Mark III


































































Search results

Summary of Contents for Standard Extreme RAKK dac Mark III

Reviews:

Related manuals for Standard Extreme RAKK dac Mark III

Brands by name

Popular brands

Raleigh Audio Standard Extreme RAKK dac Mark III, Assembly Manual

Search results

Summary of Contents for Standard Extreme RAKK dac Mark III

Reviews:

Related manuals for Standard Extreme RAKK dac Mark III

Brands by name

Popular brands