Raleigh Audio Standard Extreme RAKK dac Mark III Assembly Manual Download | Manualshive

Page: 39 / 65

background image

Wire the output jacks:

14.

Connect the output jacks with #22 wire as follows:

•

Strip the insulation from a 3” black wire so that it is bare and tin just the tips.
- Connect one end to pin 3 of the left XLR output jack.
- Feed the wire through the tab on the RCA/XLR switch that is closest to the left XLR
output jack. Solder this tab.
- Wrap the wire around the shell of the left RCA output jack and solder it to the shell.
You might want to use a solder gun to solder the shell.

•

Strip the insulation from a 3” black wire so that it is bare and tin just the tips.
- Connect one end to pin 3 of the right XLR output jack.
- Feed the wire through the tab on the RCA/XLR switch that is closest to the right XLR
output jack. Solder this tab.
- Wrap the wire around the shell of the right RCA output jack and solder it to the shell.

•

Prepare a 1¾” long blue wire and connect it between the center pin of the left RCA
output jack and pin 2 of the left XLR output jack.

•

Prepare a 1¾” long orange wire and connect it between the center pin of the right RCA
output jack and pin 2 of the right XLR output jack.

•

Prepare a 19” long #22 blue/black twisted pair.
- connect the blue wire to pin 2 of the left XLR output jack.
- connect the black wire to pin 3 of the left XLR output jack.

•

Prepare a 17” long #22 orange/black twisted pair.
- connect the orange wire to pin 2 of the right XLR output jack.
- connect the black wire to pin 3 of the right XLR output jack.

38

«
...
37
38
39
40
41
...
»

Summary of Contents for Standard Extreme RAKK dac Mark III


































































Reviews:

No comments

Related manuals for Standard Extreme RAKK dac Mark III

Brand: Patton electronics Pages: 9

CQDFX972U - AUTO RADIO/CD DECK

Brand: Panasonic Pages: 4

CQC1300U - AUTO RADIO/CD DECK

Brand: Panasonic Pages: 3

Brand: Daikin Pages: 4

Brand: HEIDENHAIN Pages: 6

Brand: DELTACAST Pages: 40

Brand: Vitek Pages: 32

Brand: Black Box Pages: 20

Y/C to NTSC Conversion PCN-40

Brand: Link Pages: 2

Brand: Wirez Pages: 16

Brand: BZB Gear Pages: 22

Brand: LC Pages: 44

Brand: foxunhd Pages: 5

Brand: Xantrex Pages: 38

Brand: S&S Pages: 3

Brand: Phenix Pages: 4

Brand: ELCART Pages: 2

Brand: Westfalia Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands