Raleigh Audio Standard Extreme RAKK dac Mark III Assembly Manual Download | Manualshive

Page: 31 / 65

background image

Mount the 5V Regulator for the I2S Adapter

♪

Skip this section if you do not have an I2S adapter.

22.

Place the 5V Regulator for the I2S Adapter in its location, on top of the 10V Regulator.
Orient the board such that the AC Input is closest to the edge of the panel. Do not secure the
board yet.

23.

Dress the grey twisted pair that is connected to transformer pins B2 and B5 along the edge of
the panel to the Regulator. Connect that grey twisted pair to the AC Input pads.

24.

Secure the board with four 6-32 x ¼” screws.

————————————————————————————

25.

Dress the wires:

•

Dress the red/black twisted pair from the USB Regulator (if present) directly across the
bottom panel.

•

Dress the red/black twisted pair from the I2S Regulator (if present) toward the front of
the bottom panel.

•

Dress the red/black twisted pair from the RAKK dac Regulator toward the front of the
bottom panel.

————————————————————————————

30

«
...
29
30
31
32
33
...
»

Summary of Contents for Standard Extreme RAKK dac Mark III


































































Reviews:

No comments

Related manuals for Standard Extreme RAKK dac Mark III

Brand: VBrick Pages: 2

Brand: VBrick Pages: 80

Brand: Zenith Pages: 54

Brand: Zenith Pages: 2

VLT AQUA Drive FC 202

Brand: Danfoss Pages: 174

Brand: Peak Pages: 8

Brand: Palmer Pages: 2

Brand: T+A Pages: 54

Brand: Versus Audio Pages: 12

AS-07UR4SYDDB15

Brand: Hisense Pages: 59

Brand: NAIM Pages: 22

VFD700-PV-40T00075

Brand: Veikong Pages: 70

Brand: ELECTROCOMPANIET Pages: 16

Brand: Viking Pages: 6

PC to TV Converter

Brand: Sewell Pages: 15

Brand: Yuan Pages: 15

Brand: de Gier Pages: 26

ProView PVR-8140

Brand: Harmonic Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands