Raisecom ISCOM6820-GP Hardware Description Download

Page: 27 / 61

Raisecom
ISCOM6820-GP (A) Hardware Description

2 Components

Raisecom Proprietary and Confidential

Figure 2-11

Panel of the GE16 card

2.5.3 Interfaces

There are 16 interfaces on the GE16 card.

Table 2-11 lists interfaces on the GE16 card.

Table 2-14

Interfaces on the GE16 card

Interface

Type

Usage

Description

1–16

SFP

Ethernet service optical
interface

Available optical module
type: 1000BASE-X

2.5.4 LEDs

There are 33 LEDs on the GE16 card.

Table 2-15 lists LEDs on the GE16 card.

Table 2-15

LEDs on the GE16 card

LED

Quantity Status

Description

SYS/ALM 1

Three
colors

System working LED



Blinking green every 1s: the card works normally.



Blinking green every 0.25s: the card is initiating and
loading.



Red (On): the system fails (the backplane fails).



Blinking red: the card is not properly inserted.



Orange (On): the card is in Standby mode.



Orange (Off): the system works abnormally.

When the card is in standby status (the orange
LED On), all other LEDs will be Off.

1000 M

Green

Interface working rate LED



Green: the interface is working at 1000 Mbit/s.



Off: the interface is working at 100 Mbit/s.

LNK/ACT 16

Green

Line working LED



Green: the line interface is connected properly.



Blinking green: the line interface is transmitting data.



Off: the line interface is disconnected or connected
improperly.

Summary of Contents for ISCOM6820-GP






























































Search results

Summary of Contents for ISCOM6820-GP

Reviews:

Related manuals for ISCOM6820-GP

Brands by name

Popular brands

Raisecom ISCOM6820-GP, Hardware Description

Search results

Summary of Contents for ISCOM6820-GP

Reviews:

Related manuals for ISCOM6820-GP

Brands by name

Popular brands