Raisecom ISCOM6820-GP Hardware Description Download Page 36

Page: 36 / 61

Raisecom
ISCOM6820-GP (A) Hardware Description

3 Fiber and cables

Raisecom Proprietary and Confidential

When connecting or removing the LC/PC fiber connector, align the connector with the optical
interface, and do not rotate the fiber. Do as below:



To connect the fiber, align the head of the fiber with the optical interface and insert the
fiber into the interface gently.



To remove the fiber, press down the clamping connector, and push the fiber head
inwards, and then pull the fiber out.

SC/PC fiber connector

Figure 3-2 shows the appearance of the SC/PC fiber connector.

Figure 3-2

SC/PC fiber connector

When connecting or removing the SC/PC fiber connector, align the connector with the optical
interface, and do not rotate the fiber. Do as below:



To connect the fiber, align the head of the fiber with the optical interface and insert the
fiber into the interface gently.



To remove the fiber, push the fiber head inwards, and then pull the fiber out.

FC/PC fiber connector

Figure 3-3 shows the appearance of the FC/PC fiber connector.

Figure 3-3

FC/PC fiber connector

When connecting or removing the FC/PC fiber connector, align the connector with the optical
interface, and do not rotate the fiber. Do as below:

Summary of Contents for ISCOM6820-GP






























































Search results

Summary of Contents for ISCOM6820-GP

Reviews:

Related manuals for ISCOM6820-GP

Brands by name

Popular brands

Raisecom ISCOM6820-GP, Hardware Description

Search results

Summary of Contents for ISCOM6820-GP

Reviews:

Related manuals for ISCOM6820-GP

Brands by name

Popular brands