Raisecom ISCOM6820-GP Hardware Description Download Page 29

Page: 29 / 61

Raisecom
ISCOM6820-GP (A) Hardware Description

2 Components

Raisecom Proprietary and Confidential

Figure 2-12

Panel of the RPA1302 power module

2.6.3 Interfaces

There is 1 interface on the RPA1302 power module.

Table 2-17 lists the interface on the RPA1302 power module.

Table 2-17

Interface on the RPA1302 power module

Interface

Usage

100–240 V 50/60 Hz

AC power interface/C13 connector socket

2.6.4 LEDs

There are 4 LEDs on the RPA1302 power module.

Table 2-18 lists LEDs on the RPA1302 power module.

Table 2-18

LEDs on the RPA1302 power module

LED

Status

Description

SYS

Green

Power LED



Green: the power supply is working properly.



Off: the device is powered off or powered on improperly.

ALM

Red

Alarm LED



Green: the power supply works abnormally.



Off: the device is not powered on or powered on improperly.

-48V

Green

Output voltage LED



Red: the device DC voltage is output normally.



Off: the device DC voltage is output abnormally.

Green

Power input LED



Red: the device external power is input normally.



Off: the device external power is not input or input abnormally.

Summary of Contents for ISCOM6820-GP






























































Search results

Summary of Contents for ISCOM6820-GP

Reviews:

Related manuals for ISCOM6820-GP

Brands by name

Popular brands

Raisecom ISCOM6820-GP, Hardware Description

Search results

Summary of Contents for ISCOM6820-GP

Reviews:

Related manuals for ISCOM6820-GP

Brands by name

Popular brands