Raisecom ISCOM6820-GP Hardware Description Download Page 48

Page: 48 / 61

Raisecom
ISCOM6820-GP (A) Hardware Description

4 Pluggable optical modules

Raisecom Proprietary and Confidential

Figure 4-2

Label of the 1000 Mbit/s SFP optical module

Table 4-1 describes the model of the 1000 Mbit/s SFP optical module.

Table 4-1

Model of the 1000 Mbit/s SFP optical module

Field

Description

USFP

Internal identifier, indicating it is a universal SFP

Transmission rate: 1.25 Gbit/s

Transmission distance:



M: 0.55 km



S1: 15 km



S2: 40 km



S3:80 km

Support DDM.

Internal identifier, different values of which indicate the same function

Comply with RoHS.

1310nm

Tx wavelength: 1310 nm

SMF

DDM

Support link detection.

21CFR (J)

Comply with U.S. DHHS 21CFR (J).

Class1

Comply with class 1 laser safety.

4.1.3 Technical specifications

Table 4-2 lists technical specifications of the 1000BASE-X SFP optical interface.

Table 4-2

Technical specifications of the 1000BASE-X SFP optical interface

Parameter

Description

Connector

LC/PC

Optical interface properties

Depend on the SFP optical module.

Working mode

Full duplex

Compliant standard

IEEE 802.3

Supported network protocol

Summary of Contents for ISCOM6820-GP






























































Search results

Summary of Contents for ISCOM6820-GP

Reviews:

Related manuals for ISCOM6820-GP

Brands by name

Popular brands

Raisecom ISCOM6820-GP, Hardware Description

Search results

Summary of Contents for ISCOM6820-GP

Reviews:

Related manuals for ISCOM6820-GP

Brands by name

Popular brands