![background image](http://html1.mh-extra.com/html/rais/viva-l-series/viva-l-series_installation-and-operation-manual_3580192051.webp)
30 / 34
OPERATING INSTRUCTIONS
FOR OEM USE ONLY
© 2016 Mertik Maxitrol GmbH & Co. KG,
All Rights Reserved.
AUXILIARY FEATURE
Upon ignition burner 1 is on and burner 2 is in the last setting.
1 2
ON
AM
PM
OFF
ON:
To switch a burner on, press the but-
ton. displayed.
OFF:
To switch the burner off, press the
button. disappears.
NOTE:
The latching solenoid valve cannot operate manually. If
the receiver battery runs down it will remain in the last
operating position.
ECO MODE
AM
ON:
Press button to enter Eco Mode.
displayed.
OFF:
Press button. disappears.
CIRCULATING FAN OPERATION
AM
Circulating fan has 4 speed levels from
low (1 bar) to high (4 bars).
SETTING:
1. Press
button and hold until
flashes.
2. Press button to increase fan speed
and button to decrease fan speed.
3. To confirm setting either press but-
ton or wait ( displayed).
OFF:
Press
button until all 4 speed level
bars disappear.
NOTE:
SETTING only. If the fan was not switched off after last
use, it starts automatically 4 minutes after ignition at max-
imum speed and goes to the last set level after 10 sec-
onds. The fan stops 10 minutes after the gas is OFF or
at pilot.
SELECTED
1
2
ON
AM
PM
OFF
ON TIME SETTING (PROGRAM 1):
7. , ,
displayed,
is displayed
shortly, and
hour
flashes.
8. To select hour press or button.
9. To confirm press button. , ,
displayed,
displayed shortly,
and
minutes
flash.
10. To select minutes press or but-
ton.
11. To confirm press button.
OFF TIME SETTING (PROGRAM 1):
1
2
ON
AM
PM
OFF
12. , ,
displayed,
is displayed
shortly, and
hour
flashes.
13. To select hour, press or button.
14. To confirm press button. , ,
displayed,
displayed short-
ly, and
minutes
flash.
15. To select minutes press or but-
ton.
16. To confirm press button.
NOTE:
Either continue to PROGRAM 2 and set on and off times
or stop programming at this point, and PROGRAM 2 re-
mains deactivated.
NOTE:
PROGRAM 1 and 2 use the same on (Thermostatic) and
off temperatures for
,
and Daily Timer ( , , , , ,
, ). Once a new on (Thermostatic) and / or off tempera-
ture has been set, that temperature becomes the new
default setting.
NOTE:
If
,
or Daily Timer are programmed for PRO-
GRAM 1 and PROGRAM 2 on and off times, these be-
come the new default times. The batteries must be re-
moved to clear the PROGRAM 1 and PROGRAM 2 on
and off times and temperatures.
or Daily Timer (
, , , , , ,
) selected
▪ Set on time and off time using same procedure as “
se-
lected
” (above).
▪
: Set on time and off time for both Saturday and Sunday.
▪ Daily Timer: Unique on and off times may be set for a single
day of the week, for multiple days of the week, or for every day
of the week.
▪ Wait to finish setting.
Summary of Contents for VIVA L Series
