7 / 34
INSTALLATION INSTRUCTIONS
FOR OEM USE ONLY
© 2016 Mertik Maxitrol GmbH & Co. KG,
All Rights Reserved.
Figure 13: Synchronization in process
NOTE:
This is a one time setting only, and it is not required
after changing the batteries in the handset or receiver.
NOTE:
Both the receiver and the handset transmit and receive
signals (bidirectional). Handset and receiver sync sta-
tus information every 10 s during first 2 min – afterward
every 4 to 6 min up to 1 h. Touching a handset button
causes an immediate synchronization.
NOTE:
When the RF receiver is placed in the appliance, the
surrounding metal can reduce reception considerably.
V Module
1. Follow wiring diagram (see figure 17, page 9). Connect the
Fan and Light first and then connect the power supply. An LED
indicates the power is ON. Use Molex connectors or connect
wires to screw terminals.
myfire Wi-Fi Box
NOTICE
The myfire Wi-Fi Box allows communication with a Home Net-
work (Wi-Fi Router) over a wireless signal. A Symax handset
must be used to achieve full functionality.
1. myfire Wi-Fi Box must be wired according to the myfire setup
diagram (see figure 20, page 12).
2. myfire Wi-Fi-Box must be connected to the receiver; connect
receiver to mains power. After 30 seconds the myfire Wi-Fi Box
goes into Access Point Mode (green LED flashes). Go to “my-
fire App Setup” on page 15 to configure the Wi-Fi Router.
NOTICE
If mains power is lost, disconnect the myfire Wi-Fi Box from
the receiver. This will prevent receiver batteries from being
drained quickly.
NOTICE
Multiple users on the same Wi-Fi channel may interfere with
the data transfer. Press reset button on the myfire Wi-Fi Box
for 1 second to change current channel.
NOTICE
If myfire Wi-Fi Box is not connected to the receiver or is not used,
it will leave the Access Point Mode (AP Mode) after 24 hours.
NOTICE
If you have multiple fireplaces using myfire Wi-Fi Boxes, the
minimum distance between the myfire Wi-Fi Boxes must be 60
cm (2'). A shorter distance may interfere with the data transfer.
MINIMUM REQUIREMENT WI-FI ROUTER:
▪ Compatible with IEEE 802.11n/g/b
▪ WPA2 encryption
▪ Radio frequency: 2,4 GHz band
▪ Wireless auto channel: Automated search for WLAN radio
channel free of interference
MINIMUM REQUIREMENT SMART DEVICE:
▪ IOS 8.0 or Android 4.4
LED INDICATION ON MYFIRE WI-FI BOX (SEE FIGURE 14):
Label
LED
Status
Power
Blue
On
Power on
Off
Power off
WLAN
Green
On
Connected to Home Network (Wi-Fi Router)
Off
Not connected to Home Network (Wi-Fi Router)
Flashing myfire Wi-Fi Box in Access Point Mode
Receiver Blue
On
Receiver connected
Off
No Receiver connected or connection lost
All LEDs
Flashing Internal configuration
Figure 14: LED on myfire Wi-Fi Box
RESET STATUS ON MYFIRE WI-FI BOX:
Press
Reset
Button
LED status
Blue Power LED
Function
1 sec
Continuously flashes
every ½ sec
Activates AP Mode for 10 min (time to connect
myfire Wi-Fi Box to Home Network (Wi-Fi Router)).
Simultaneously the Wi-Fi channel changes.
5 secs
Two rapid flashes
every 1 sec
System reset
10 secs Flashes every 100 ms
(continuously)
Restores factory firmware (myfire Wi-Fi Box will set
to default after reboot); takes up to 2 min
20 secs Flashes every 50 ms
(continuously)
Restores factory firmware and erases all data
not locked (Wi-Fi network will set to default after
reboot); takes up to 2 min
Reset button
(Use paper clip to push button)
Figure 15: Reset Button myfire Wi-Fi Box
Summary of Contents for VIVA L Series
