background image

 

 

 

STARTUP & PROGRAMMING 

The control valve is pre-programmed at factory. You can however change the default settings or to change regeneration 
frequency. We recommend setting backwash every 3 days with a minimum 10 minute backwash and 5 minute rinse cycle. If 
you have questions about programming, please call Rainfresh at 1800-667-8072. 

When power is first supplied, the valve electronics may take up to two minutes to initialize.  During this time the screen will 
show “INTIALIZING WAIT PLEASE”.  Do not touch any buttons at this time.  When the valve reaches the service position, it 
will display the following information in sequence:

  

 

1.

 

Date & Time 

2.

 

Regeneration Days/Capacity 

3.

 

Remaining Days/Volume Remaining 

4.

 

Regeneration Time 

5.

 

Last Regeneration Date 

6.

 

Current Flow Rate (GPM) 

7.

 

Peak Flow Rate (GPM)

The control valve has a display screen and 4 buttons 

 

 

 

 

 

 

 

 
 
 
 
 
 
 

 
VALVE PROGRAMMING

 

The valve has 2 levels of programming – Level 1 and Level 2 
You will need to only go through Level 1 programming to start up your unit. Level 2 programming is factory set 
and can be changed only if desired. 
 
Level 1 programming allows you to set  

1.

 

Current time 

2.

 

Current date 

3.

 

Vacation mode  

 

 
 
 
 
 
 
 
 
 
 

MENU BUTTON

 

“ ” 

The function of this key is to 
enter the level one 
programming mode where the 
valve settings can be adjusted. 

SET / REGEN BUTTON

 

” 

This button has two functions.  The first is to initiate a 
manual regeneration by holding the button for 3 or 
more seconds.  The second function is while in 
programming mode, pressing this key allows the user to 
change the value of each setting. 

UP / DOWN

 

” 

These buttons are used to 
increase or decrease the value 
of the settings while in the 
programming mode. 

Summary of Contents for CAFE 948










Reviews: