Raider R50-001 Owner'S Manual Download Page 40 | Manualshive

Page: 40 / 40

background image

39

15. Emergency Tool Kit

Spark Plug Socket
Three (3) Spark Plugs
Pliers
Screwdriver
Socket for removal of pull starter
Pull Rope
Slit Pin

16.

EPA Emissions Regulations

EPA (United States Environmental Protection Agency) has emission regulations and

is

controlling air

pollution from new outboard motors. The Raider motor does not meet EPA regulations as it can
burn  heavy  fuels  (JP-5/8).    As  a  result  Raider  has  received  an  exemption  under  the  National
Security Act to operate these engines in the United States.  A sticker has been applied to the side
of the Raider indicating authorization of EPA.  The Raider motor is only sold to the military.

«
...
38
39
40

Summary of Contents for R50-001









































Reviews:

No comments

Related manuals for R50-001

Brand: Abit Pages: 72

Brand: Intel Pages: 76

Brand: ECS Pages: 46

STEVAL-IME008V1

Brand: STMicroelectronics Pages: 19

Brand: IBASE Technology Pages: 76

Brand: IBASE Technology Pages: 91

tKINO-AL-E1-R10

Brand: IEI Technology Pages: 12

Brand: Texas Instruments Pages: 27

Brand: DFI Pages: 48

Brand: ON Semiconductor Pages: 5

Brand: MSI Pages: 92

Brand: Watersnake Pages: 24

Brand: ASROCK Pages: 66

Brand: Texas Instruments Pages: 17

miriac SBC-T104 Series

Brand: MicroSys Pages: 70

Brand: Microstar Computers Pages: 104

Brand: Shuttle Pages: 65

Brand: Zida Pages: 55

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands