Raider R50-001 Owner'S Manual Download

Page: 35 / 40

Lower
Unit

Pro-
peller

0 Bend of blades

damage and wear

Gear
oil

Change of oil and
water leak eval.

Water
pump

Check for
Wear or damage

Replace

impeller -12
months

Bolt and Nuts

0 Retighten

Rotating Parts

Grease Nipples

Apply and pump
in grease.

DGrab Bar

Check for

tightness

Fuel Ind.

"' System

(Carb.)

(

Visual

Idle, high speed
issues.

Repair or
replace.

Cables

Cover

Outer Equipment

Check corrosion

Anode

0 Check corrosion

and defamation

Replace

10-7 Changing Gear Oil:

Remove the oil plugs (upper and lower), and drain the gear oil completely.

Insert the oil tube nozzle in to the lower oil plug hole, and squeeze the tube until the oil flows

out of the upper plug hole.

Re-install the upper oil plug. Then remove the oil tube nozzle and install the lower oil plug.

Upper oil plug

Lower

Oil

Plug
hole

Summary of Contents for R50-001









































Search results

Summary of Contents for R50-001

Reviews:

Related manuals for R50-001

Brands by name

Popular brands

Raider R50-001, Owner'S Manual

Search results

Summary of Contents for R50-001

Reviews:

Related manuals for R50-001

Brands by name

Popular brands