Raider 40 Operator'S Manual Download Page 3

Raider Operators Manual                                                                                     R40ES-001-15-1 

 

1. 

Your Raider 40  Outboard Motor

 

a.

 

Limited Warranty 

 

This Raider product is fully guaranteed against defective materials and workmanship for 
the period on one year from date on DD-250 form.   The limited warranty will not apply to 
normal wear and tear of parts, adjustments, tune-ups, or to any damage caused, but not 
limited to careless use. 
 
Raider has taken every advantage using non-corrosive materials, high quality and high 
reliable parts. This multi-fuel, submersible outboard has been built for ruggedness and 
durability to meet war 

fighter’s

 needs. After missions the motor should be washed with 

soap and water and let dry.  Fuel should be run out prior to storage. 
 
The limited warranty does not cover maintenance items.  The following items are a few 
examples not covered by the limited warranty: spark plugs, Anode, Propeller, Fuel filter, 
Oil filter, Starter rope, Shear-pin, Rubber goods, water pump impeller, oil seal, vinyl tub-
ing, and battery. 
 
The limited warranty will not cover the boat the product is mounted on, trailer, equip-
ment, or accessories associated with the product. 
 

b.  Serial Number                                                           

 

The serial number is located on the engine block-near heads. 
 

c.  Safety/Danger/Warnings/Cautions  

Before operating the Raider outboard motor, be sure to thoroughly read and understand 
this Users manual and follow all of the instructions shown.  Of particular importance in-
formation preceded by the words or symbols draw attention to safety issues.  This man-
ual contains information that can help prevent personal injury and damage to equipment. 
Understand the following symbols before proceeding: 
 
All motors with electric start will start in gear.  User has responsibility to insure Raider is 
in neutral before starting.  Operator assumes responsibility for this operation. 



Battery 

Battery must be safely maintained and cannot 

 under any circumstances- 

Take a “fast” charge.  A battery “maintainer” is provided and should be 

used when motor is being stored.  The battery will recharge upon running 
of the Raider Outboard.  Primary method of start 

 Pull Starter. 

 

 Safety Warning: When replacement parts are required, use genuine Raider parts, or 

parts with equivalent characteristics, including type, strength, and material.  

 

All photographs and illustrations used in this manual may not depict actual models or equip-

ment, but are intended as representative views for reference only. 

 

 d.  Features of Raider Outboard 

      - Electric start with battery located under cowling 
      - Grab handle for easy movement of motor on land and in water 
      - Transom plates for easy installation onto RIB 
      - Dewatering lever to dewater both pistons/heads and fuel 
      - Lightweight 

 under 150 lbs. 

Summary of Contents for 40


























Reviews: