manualshive.com logo in svg

RAE-SAN V1.02 OBD-Bridge, Installation Manual

Share
Download
RAE-SAN V1.02 OBD-Bridge Installation Manual Download Page 31

 

Page : 31 

 

the control of Rae-San (and/or Entities Trading as Rae-San). Rae-San (and/or Entities Trading as Rae-

San) shall not be responsible for any type of incidental, consequential, or special damages. All 

implied warranties, including but not limited to those warranties of fitness and merchant 

accountability, are limited in the total duration to 12 months from the original purchase date. If the 

warranty occurs within 30 days from the date of purchase, please contact the dealer the product 

was purchased from. Over 30 days from the date of purchase, please contact Rae-San (and/or 

Entities Trading as Rae-San) direct at [email protected]. Customer must contact Rae-San 

(and/or Entities Trading as Rae-San) prior to sending warranty product. Claims for lost shipment, 

damaged shipments, or other problems regarding freight must be made directly to the responsible 

carrier. Warranty is solely through Rae-San (and/or Entities Trading as Rae-San). Service to our 

products by anyone other than Rae-San (and/or Entities Trading as Rae-San) authorized installation 

centers voids warranty. Rae-San (and/or Entities Trading as Rae-San) disclaims any and all liability for 

consequential or incidental damages. Rae-San (and/or Entities Trading as Rae-San) will not be held 

responsible for personal damage, bodily harm or any other legal matters.  

 

 

 

 

Summary of Contents for V1.02 OBD-Bridge
































Reviews:

No comments

Brands by name

Popular brands

Load more brands