background image

 

 

PRECAUTIONS 

 

Prior  to  installation,  use  or  maintenance  activities,  carefully  read  this  user 
manual and follow the provided guidelines. 

 

 

Prior to the first use, carefully read this user  manual. Use the device only 
as intended. 

 

Protect the indicator against considerable temperature variation, solar and 
UV radiation, substances causing chemical reactions. 

 

The  weighing  device  must  not  be  operated  in  hazardous  areas 
endangered with explosion of gases, and in dusty environments. 

 

In case of damage, immediately unplug the device from the mains. 

 

Scales  to  be  decommissioned  must  be  decommissioned  in  accordance 
with valid legal regulations. 

 

Do  not  let  battery  discharge  in  case  of  prolonged  storage  of  the  device  
in low temperature. 

 

A  worn  out  battery  can  be  replaced  only  by  the  manufacturer  or  by  the 
authorized service. 

 

Accumulators  do  not  belong  to  regular  household  waste.  The  European 
legislation requires discharged accumulators to be collected and disposed 
separately  from  other  communal  waste  with  the  aim  of  being  recycled. 
Symbols  on  batteries  identify  harmful  compounds:  Pb  =  lead,  
Cd = cadmium, Hg = mercury. Dear user, you are obliged to dispose of the 
worn out batteries as regulated. 

Summary of Contents for PUE H315





























Reviews: