RadonTec AlphaFreshbox 200 WiFi Manual Download Page 51

Page: 51 / 63

Manual

–

AlphaFreshbox 200 WiFi

Emergency stop

In emergency situations, the system is switched off and the
display

flashes

the

alarm

code:

•–

short light signal

—

–

long light signal

Alarm code

Alarm description

—

Outdoor temperature sensor missing

—

•

Short circuit on outdoor air temperature sensor

—

•

—

Sensor behind the heating coil missing

—

•

Short-circuit on sensor after the post-heating coil

—

•

—

Exhaust air temperature sensor before the heat
exchanger is missing

—

•

—

•

Short circuit on extract air sensor

—

•

—

Exhaust air temperature sensor after the heat
exchanger is missing

—

•

Short circuit on the sensor after the heat exchanger in
the extract air duct

—

•

—

Reserved

—

•

—

•

Reserved

—

•

—

•

—

Sensor behind the heat exchanger in the supply air
duct is missing

—

•

—

•

Short circuit on the sensor after the heat exchanger in
the supply air duct.

—

•

—

Empty battery. The time-controlled operation will not
work correctly.

—

•

—

•

Reserved

—

•

—

Fire alarm activation

—

•

Remote control connection error with the control unit
(not shown in the app).

•

—

Wifi module initialisation error

•

Unknown error (contact your dealer if this error
occurs).

Summary of Contents for AlphaFreshbox 200 WiFi
































































Search results

Summary of Contents for AlphaFreshbox 200 WiFi

Reviews:

Related manuals for AlphaFreshbox 200 WiFi

Brands by name

Popular brands

RadonTec AlphaFreshbox 200 WiFi, Manual

Search results

Summary of Contents for AlphaFreshbox 200 WiFi

Reviews:

Related manuals for AlphaFreshbox 200 WiFi

Brands by name

Popular brands