RadonTec AlphaFreshbox 200 WiFi Manual Download Page 53

Page: 53 / 63

Manual

–

AlphaFreshbox 200 WiFi

Troubleshooting

Malfunction

Possible reasons

Remedy

The fan(s) do not
start when the
system is switched
on.

No power supply

Check whether the power supply
is connected correctly. If not,
rectify the connection error.

Cold supply air

Dirty exhaust air
filter

Clean or replace the exhaust air
filter.

Icing of the heat
exchanger

Check the heat exchanger for
icing. If necessary, switch off the
ventilation system and allow the
ice to melt.

Failure of the
heating coil

Contact your dealer.

Low flow rate

Dirty filters, fans and
heat exchangers

Clean or replace the filters, clean
the fans and the heat exchanger.

Clogged or damaged
ventilation system

Check for unobstructed opening of
diffusers and louver shutters,
check the exhaust hood and the
supply grille and clean those, if
necessary. Make sure the air ducts
are clean and intact.

Loud noise,
vibrations

Dirty fan impellers Clean the impellers.

The screw
connection is loose.

Tighten the fastening screws.

Summary of Contents for AlphaFreshbox 200 WiFi
































































Search results

Summary of Contents for AlphaFreshbox 200 WiFi

Reviews:

Related manuals for AlphaFreshbox 200 WiFi

Brands by name

Popular brands

RadonTec AlphaFreshbox 200 WiFi, Manual

Search results

Summary of Contents for AlphaFreshbox 200 WiFi

Reviews:

Related manuals for AlphaFreshbox 200 WiFi

Brands by name

Popular brands