background image

32 

7.  Troubleshooting 

 

Problem 

Solution 

The radiator does not switch on.  

Check that the power supply is on and that it is as indicated 
in  the  radiator's  nameplate  (e.g.  230  Vac  50  Hz),  and  that 
the main switch on the right side  of the radiator is  switched 
on (position "I").  

The radiator does not heat up.  

Make  sure  that  the  operating  mode  is  as  required  and,  if 
using a preset programme, that you are not in a time period 
for which anti-freeze mode is set.  
If  the  ambient  temperature  is  higher  than  that  set,  the 
radiator should not heat up.  
If  in  doubt,  set  Comfort  mode  and  a  required  temperature 
much higher than the ambient temperature, to check that the 
radiator is working properly.  

The radiator stays hot.  

Check  that  the  temperature  setting  is  not  too  high  or  that 
there  are  no  draughts  on  the  radiator,  altering  the  ambient 
temperature measured.  

The radiator does not heat up enough.  

Check  that  the  temperature  setting  is  not  too  low,  that  the 
radiator is only heating the room in which it is installed (keep 
the  doors  closed)  and  that  the  mains  power  supply  is 
correct.   

The radiator heats in Eco mode.  

The  radiator  may  heat  up  to  reach  /  maintain  the  eco 
temperature.  This is not abnormal operation.    

The radiator's surface is very hot.  

It  is  normal  for  the  surface  to  be  hot  when  working.    The 
maximum  values  comply  with  the  limits  laid  down  by 
applicable safety norms.  
If  the  radiator  is  always  very  hot,  it  may  be  undersized  for 
the  space  in  which  it  is  used,  or  may  be  affected  by 
draughts.  

The  temperature  in  the  room  differs  from  the 
temperature set.  

Having waiter for the ambient temperature to stabilise for at 
least  4  hours,  you  may  have  to  compensate  for  any 
differences  between  the  temperature  indicated  by  the 
radiator and that measured in the room.  To do this see the 
contents  of  paragraph  6.3  on  the  section  "Aligning  the 
outside temperature".  

The radiator gives off an unpleasant odour.  

When  the  radiator  is  new,  it  is  possible  that  when  it  begins 
working  for  the  first  time  an  unpleasant  odour  may  be 
sensed.  This  is  due  to  residue  from  the  manufacturing 
process.  
Radiators  that  have  already  been  used  may  give  off 
unpleasant odours if they are not used for a long time and/or 
if they are used in polluted spaces with poor quality air.  

 

 

8.  Maintenance 

 

This product does not require any special maintenance. 

 

Clean the product, especially the heating panel, with a dry cloth once every 6 months. 

 

If the product requires repairing, contact an authorised technical service centre. 

 

When replacing the power cable, use  a 2x1,00mm

2

 or 3x1,00mm

2

 H05V2V2-F HAR type, depending  on the version. 

This operation, for cables both with and without plugs, must be performed by qualified personnel and never by the end 
user in order to avoid damaging the appliance and jeopardising personal safety. 

 

9.  Legal notice 

Environment and recycling 

Please help us to protect the environment by disposing of the packaging in accordance with the national 
regulations for waste processing. 

Recycling of obsolete appliances 

Appliances with this label must not be disposed off with the general waste. They must be 
collected separately and disposed off according to local regulations. 

 

Summary of Contents for KLIMA Series



















Reviews: