background image

Replacement Lamps

STL360Q1

150 watt double-ended quartz flood 

STL360Q2  (2 lamps)         150 watt double-ended quartz flood

STL360Q3     

300 watt double-ended quartz flood

STL360H    (2 lamps)         150 watt PAR38

STL360HB  (2 lamps)         150 watt PAR38

NOTE: All double ended quartz fixtures must be mounted with
the lamp horizontal, or parallel to the ground.  If the fixture is 
tilted, the lamp will fail prematurely.

Limited Warranty

Your STL360 will be replaced or repaired, at our option, if it
proves to be defective in workmanship or materials within ten
years from the date of original purchase.

For repair replacement, return the product freight prepaid and
insured to 

RAB Lighting/170 Ludlow Avenue/Northvale,

NJ 07647.

The STL360 should be packed carefully.  Please

include your sales receipt and a description of the problem.

If your unit is out of warranty, or the damage is unrelated to the

 

original manufacture, return your unit directly to us with a check

 

for $

3

0.00 (made out to RAB Electric). We will repair or replace

 

your unit.

Under no circumstances shall we be liable for any incidental or
consequential damages arising out of or in connection with the
use or performance of this product or other indirect damages
with respect to loss of property or revenue or cost of installation,
removal or re-installation. This warranty gives you specific legal
rights and you may also have other rights which vary from state
to state. 

Contents of Accessory Kit

2 Lens Masks

Indoor Switchplate Label

3 Wire Nuts

Adjustment Tool

Mylar Lens Mask

Crossbar 
with Green Ground Screw

Hanging Hook

1/2" Close Up Plugs (3)

Slotted Screws (4)

Finishing Cap

O-ring Gasket

Center Mounting Screw

Foam Gaskets (2)

Metal Plate

MAKES

IT

EASY!

Easy Installation & Product Help

Toll Free Phone

Toll Free Fax 

Fax on Demand 

Call our friendly experts.

Send faxes to RAB

Faxed information,

8AM - 6PM ET Mon. - Fri.

24/7.

24/7.

888 RAB-1000

888 RAB-1232

888 RAB-1236

E-mail

www.rabweb.com

Questions and requests

Visit our internet site

answered promptly

for product information

t

[email protected]

RAB Lighting
170 Ludlow Avenue Northvale, New Jersey 07647 U.S.A.

© RAB Lighting 2004

Incorrect

Correct

22

21

Summary of Contents for STL360H













Reviews: