background image

/RDS-TFT2HE, /RDS-TFT3HE & /RDS-TFT4HE

ELETTRONICA

23

 

/ 34

User Manual

Rev. 1.0 - 01/02/22

The 

DI

 represents the characteristics of radio transmitted signal and the presence 

or absence of remote control of “TA” inside PTY.

The 

PTY

 represents the characteristics of the Radio programming (eg. SPORT), if 

they are musical or spoken (active MS means music) and if it has the capacity to 

handle traffic information (active TP), and if in that moment is transmitting (active 

TA). 

The 

RDBS/RDS

 is a field that has no effect on sent data from device while it is 

used from operator to interpret correctly the PTY, indeed the codes from 0 to 31 

have a different meaning depending on whether a European RDS or an RBDS.

The 

PTYN

 is the field called “extension” of PTY, it is transmitted only if at least one 

10A group will be inserted in the sequence of DNS transmission groups.

The PIN is a code that identifies a program, it has been included in this software 

just for test, indeed this field should be changed in real time during programming 

to allow listeners to be notified when their favorite program starts. It should not be 

set in this dialog box but sent with a continuous data stream. The PIN is transmitted 

only if at least one 1A group will be inserted in the sequence of DNS transmission 

groups.

The 

ECC, Language

 are two fields that have no effect on the graphical interface, 

in other words the operator will continue to see the windows in the language set on 

the operating system (WINDOWS) but activating the transmission of Group 1, the 

receivers will treat the radio-texts with the fonts defined in “Language”. In addition, 

the “ECC” field change the country code of the IP. Pay attention, the reading of 

devices that do not have a programmed “ECC” will result as “USA + number from 

1 to 9 or a letter from A to F”, because in America the zones are defined by the 

codes while in rest of the world each state has its own code.

Other 7 PSN configurable in the same way as “Main-PSN” are available for each 

DNS. Using the “Enable DNS/PSN” you can enable the transmission “14A/14B” 

groups of data relating to other radio 

(EON-1 … EON-7)

 up to a maximum of 7.

Summary of Contents for RDS-TFT2HE









































Reviews: