background image

 
 

 

Troubleshooting

 

 

 

Service & repair should only be performed by R-Tech welding trained personnel. Unauthorized 
repairs performed on this equipment may result in danger or injury to the technician and machine 
operator and will invalidate your warranty. For your safety and to avoid electric shock, please 
observe all safety notes and precautions detailed throughout this manual  
  
The troubleshooting guide is provided to help you locate possible machine malfunctions  
  
If fault / problem is not listed below check our  Mig Welder Support  page on our website:   

www.r-techwelding.co.uk/support.php

  or contact R-Tech by phone. Contact details can be found 

on our website  

 
 

 Output Problems

 

 

 

No output - Power light is not lit 

 

Check machine on/off switch is in the ‘on’ position Check Input power to machine Check plug 
wiring Check mains trip / fuses

   

 

 

No output - Fan runs - Power light is lit  

Check torch connections are secure and torch switch operation, try replacing MIG torch.

  

  

 

No output - Power light is lit - Warning light is lit  

Welding application may have exceeded recommended duty cycle, allow machine to cool 

down until the warning light goes out.  

 

 

 

No output – Power light is lit – Gas at torch tip – No wire feed  

Check wire feed unit protecting fuse on rear of machine, if blown replace with new fuse of 

same rating, if the fuse blows again contact R-Tech

    

 

Machine keeps overheating - Warning light is lit on machine   

Check if fan is running – if not contact R-Tech. Check the cooling vents for obstruction, blow 

out machine with clean dry low pressure air supply.  Check for adequate ventilation 
around machine

   

 

Porosity in weld – No / low gas at torch tip   

Check gas supply from gas bottle  Check flow rate on regulator  Check gas hose for 

restrictions  Check for draughts in local area, open doors etc  Replace MIG torch – may 
have gas restriction

   

 

Poor weld penetration  
 

Check condition of earth lead and clamp and ensure clamp is connection via a clean area on 

work piece. Check the condition of the MIG torch, try another MIG torch

.

 

Summary of Contents for I-MIG160 MIG




















Reviews: