background image

                                         

 

 

Introduction   

 

The R-Tech I-MIG160 is a member of our highly acclaimed family of welding products.   
Premium features include:

-  

  

1. Inverter power source – more efficient to operate, provides smoother weld characteristics 

than traditional welders  

2. Infinite welding voltage to allow fine tuning of weld characteristics  
3. Adjustable arc force – controls splatter – ideal for automotive work  
4. Digital amp & volt meters  
5. Euro type torch fittings for easy torch fitment/replacement  
6. 35% Duty cycle at 160 Amps @ 40C  
7. 60% Duty cycle at 110 Amps @ 40C  
8. Lightweight and portable – Ideal for maintenance and mobile welders    

 
  

Recommended Processes 

  
The R-Tech

 IMIG 160

 is recommended for the MIG welding processes within its output capacity 

of 160 Amps DC  

 

 

Equipment Limitations  
 

 

The R-Tech 

IMIG 160

 is protected from overloads beyond the output ratings and duty cycle as 

per machine specifications with thermostat protection of the output coils and rectifiers.  
  
  

Welding Capability – Duty Cycle 
 

 

The R-Tech 

IMIG 160

 is rated at 160 Amps at 35% and 110 Amps @ 60% duty cycle on a ten 

minute basis. If the duty cycle is exceeded a thermal protector will shut the machine off until it 
cools.  

  

 

Technical Specifications 

 

 

 

Model No.  

 R-Tech IMIG 160  

  

  

  

  

Input  

  

240V AC 50/60Hz  

  

  

  

  

  

  

MIG Operation  

Fuse Rating  

13A 

  

Rated Output Current  

160Amps Max  

  

Generator required KVA  

4.8KVA  

  

Duty Cycle @ 160 AMPS  35% @ 40

º

C  

  

Duty Cycle @ 110 AMPS  60% @ 40

º

C  

  

Duty Cycle @ 85 AMPS  

100% @ 40

º

C  

  

Output current Range  

30-160 AMPS  

MMA Operation 

Fuse Rating 

13A 

Summary of Contents for I-MIG160 MIG




















Reviews: