QubicaAMF 400288005, Installation Manual, Page: 48 / 147

Console pedestal assembly BES X installation manual
38 P/N: 400288005; Rev: L, 09/21
T.10.041 – 286002800 single and 286002827 short single pedestal assembly
instructions
[ ] 120
4.72
[ ] 120
4.72
[ ] 54.8
2.16
[82]
3.23
[60]
2.36
[12]
.47
[ ] 60.3
2.37
[ ] 60.3
2.37
[ ] 299.4
11.79
[ ] 197.7
7.79
[ ] 98.9
3.89
REAR OF PEDESTAL
FRONT OF PEDESTAL
CABLE
PASSAGE
PLAN VIEW
B
4X standard mounting
positions marked ‘A’
2X alternate mounting
positions marked ‘B’
5
15
3
12
13
2
11
7
17
10
1
19 18
20
21
B
6
INSTALLATION INSTRUCTIONS
1. Un-pack pedestal,
2. Remove mounting hardware stretch wrapped to extrusion (item 3).
3. Remove V-Support back (item 5) secured by 2 PHPMS M5-,8 X 25 SCREWS (item 15).
4. Remove front & rear base covers (items 6 & 7) secured by 4 FHPMS M4-,7 X 16 ZN screws (item 17).
5. Position pedestal on the floor in the desired position and orientation.
NOTE : Please install the pedestal in a position far enough away from the ball rack to avoid potential damage caused by bowling balls falling from
the ball rack.
6. Mark/transfer the mounting holes in base sheet metal - lower (item 1) to the floor.
NOTE : if the standard mounting hole positions marked ‘A’ in the plan below interfere with the cable conduit in the floor, use both of the alternate
positions marked ‘B’ in the plan view below for the supplied anchors.
7. Remove base sheet metal - lower (item 1) from base sheet metal - upper (item 2) secured with 8 each of HHCS M5-,8 X 16 (item 12) & SWM M8
D-127A ZN (item 13).
8. Position base sheet metal - lower (item 1) on the floor and install with the appropriate supplied anchors. For wood floors drill Ø 1/4 holes and
secure using 4 or 5 each of FW 0.41 X 0.73 X 0.06 ZN (item 19), SWM 3/8 ANSI ZN (item 18), and HHLB 3/8 X 2.00 ZN (item 20). For concrete
floors drill Ø 3/8 holes to a minimum depth of 3-1/2 inches [89mm], clear the holes of all debris and secure using 4 or 5 each of FW 0.41 X 0.73
X 0.06 ZN (item 19), SWM 3/8 ANSI ZN (item 18) and ANCR TB 3/8 X 3.00 ZN (item 21). Drive taper bolt into place leaving 3/16 inch [4.8mm]
head clearance. Tighten taper bolt to minimum of 40FT-LB [54 Nm].
NOTE : extra flat washers FW 0.41 X 0.73 X 0.06 ZN are included for leveling purposes; if not needed discard.
9. Install console cables thru the anti-short bushing (item 10) and thru the extrusion (item 3).
10. Re-install pedestal on base sheet metal - lower and secure with 8 each of HHCS M5-,8 X 16 (item 12) & SWM M8 D-127A ZN (item 13).
11. Re-install front & rear base covers (items 6 & 7); secure using 4 FHPMS M4-.7 X 16 screws (item 17).
12. Install keyboard or LCD assembly and connect per instructions provided with keyboard or LCD.
13. Re-install V-Support back (item 5); secure using 2 PHPMS M5-.8 X 25 screws (item 15). Take care not to pinch any wires or cables.
B
B