background image

8

9

7. Connect the other end to the rear spigot 

sticking up at the water heater. Do this by cut-

ting the length back so that you don’t have too 

much pipe in use. The run should be as long as 

necessary to make a smooth connection with-

out stretching the pipe. Use the spring clips to 

secure them in place.

DO NOT TURN ON THE POWER

This step is handled in the commissioning

guide.

NOTE

The venturiT™ is a unique device that enables 

the boiler to vent itself to drain.

During the heating cycles, water expansion 

would otherwise push boiling water out of 

the spout without activating the boiling func-

tion. It’s essential to install it running the pipe 

down-hill.

NOTE

If using an RO system, you must ensure it 

delivers water at 45-60psi (3-4bar) at all 

times. You may need to add a pump to ensure 

the optimum psi is supplied to the Quatreau 

system.

During commissioning, use only mains water, 

then convert to RO once the system has been 

set up and commissioned. 

NOTE

Inside the fitting kit are 4x ¼” (6.35mm) stems 

elbows that can be inserted into the chiller to

make it easier to install the interconnections 

without kinking the pipe.

NOTE

Ensure that you leave a 1” (25.4mm) gap 

around the chiller unit’s sides, enabling ven-

tilation and air movement, without which the 

system will not chill correctly.

DO NOT TURN ON THE POWER TO THE 

CHILLER OR DAMAGE WILL OCCUR

This step is covered in the commissioning 

manual.

End of the installation manual. Now refer to 

the commissioning manual.

8. The other pipe that comes out of the ventu-

riT™ should now be connected to the top of the 

Type AA airgap drain. Cut it back if to a reason-

able length but not so short that it is stretched. 

The pipe should run downhill so that water can 

escape by gravity.

9. Using the final piece of silicone in the fitting 

kit, connect the front spigot (this feeds chilled 

and sparkling water) to the remaining pipe. En-

sure you do not pull on the pipe coming from 

the spout. 

1.  Site the chiller unit to the left of the water 

heater over the ventilation duct.

2. Use the 1/4”(6.35mm) blue pipe provided to 

interconnect the QST553-B and CS20 unit as 

follows.
a. H20 OUT on the 553-B into WATER IN on the 

chiller.

b. CO2 OUT on the 553-B into C02 GAS IN on 

the chiller.

c.  SODA WATER OUT on the chiller to CARB IN 

on the 553-B

d.  STILL WATER OUT on the chiller to CHILLED 

IN on the 553-B

SECTION SIX

INSTALLING THE QUATREAU 

CHILLER CARBONATOR

CONNECTING WATER SUPPLY

INSTALLING WATER CHILLER CARBONATOR

Summary of Contents for SMARTTAP 553-B









Reviews: