Quasonix QSX-RDMS-RM Series Installation And Operation Manual Download Page 83 | Manualshive

Page: 83 / 190

Quasonix QSX-RDMS-RM Series Installation And Operation Manual Download Page 83

Rack-Mount RDMS

TM

Telemetry Receiver

68

Quasonix, Inc.

Figure 121: Advanced Menu, Muting Selection

The user may toggle the Muting value On or Off by pressing the Enter key on the front panel keypad until the
desired value displays.

4.1.5.17 Muting Timeout

The Muting Timeout option, shown in Figure 122 is used to set a timeout value (in milliseconds). This setting is
used to determine when to mute (stop sending data) when the Muting option is set to On.

Figure 122: Advanced Menu, Muting Timeout Selection

A dialog screen displays prompting the operator to enter a new Muting Timeout value (in milliseconds) using the
rack’s front panel numeric keypad. The valid range is 0 to 46016 milliseconds. The Muting Timeout Entry screen is
shown in Figure 123. When the new value is entered, press the Enter key on the keypad.

«
...
81
82
83
84
85
...
»

Summary of Contents for QSX-RDMS-RM Series































































































































































































Reviews:

No comments