Quasonix QSX-RDMS-RM Series Installation And Operation Manual Download Page 71

Page: 71 / 190

Rack-Mount RDMS

Telemetry Receiver

Quasonix, Inc.

4.1.5.10 Advanced Menu

The Advanced Menu should only be accessed by advanced users. Contact Quasonix customer support before using
these options.

The Advanced Menu, which is accessed via the Main Menu, as shown in Figure 101, provides access to the
following options:

•

Sync Measured Bit Rate

•

IF Filter

•

Video Filter

•

Video Scale

•

Video Invert

•

Video DeEmphasis

•

Phase Noise Compensation

•

Tape Output

•

Tape Frequency

•

Muting

•

Muting Timeout

•

Mod Scaling Menu

•

Encoding Menu

•

Convolutional Decode

•

SNR Estimator

•

Factory Default

Figure 101: Main Menu, Advanced Menu

Summary of Contents for QSX-RDMS-RM Series































































































































































































Search results

Summary of Contents for QSX-RDMS-RM Series

Reviews:

Quasonix QSX-RDMS-RM Series, Installation And Operation Manual, Page: 71 / 190

Search results

Summary of Contents for QSX-RDMS-RM Series

Reviews: