background image

A Quantum Rehab Provider or a qualified technician 

must perform the initial setup of this power chair and 

must perform all of the procedures in this manual.

The symbols below are used throughout this owner’s manual 
and on the power chair to identify warnings and important 
information. It is very important for you to read them and 
understand them completely.

Indicates a potentially hazardous condition/situation. 

Failure to follow designated procedures can cause either 

personal injury, component damage, or malfunction. On 

the product, this icon is represented as a black symbol 

on a yellow triangle with a black border.

These actions should be performed as specified. Failure 

to perform mandatory actions can cause personal injury 

and/or equipment damage. On the product, this icon is 

represented as a white symbol on a blue dot with a white 

border.

These actions are prohibited. These actions should 

not be performed at any time or in any circumstances. 

Performing a prohibited action can cause personal 

injury and/or equipment damage. On the product, this 

icon is represented as a black symbol with a red circle 

and red slash.

Copyright 

©

 2019

INFMANU4800/Rev D/October 2019

SAFETY GUIDELINES

MANDATORY!

PROHIBITED!

WARNING!

WARNING!

WARNING!

Intended Use

A wheelchair component is a device intended for medical 
purposes that is generally sold as an integral part of 
a wheelchair, but may also be sold separately as a 
replacement part.

Regarding Devices for Prescription Use

CAUTION! Federal law restricts this device to sale by or 

on the order of a physician or other certified personnel 

licensed by the law of the State (US only) or region in 

which this personnel practices to use or order the use 

of the device.

NOTE: These instructions are compiled from the latest 
specifications and product information available at 
the time of publication. We reserve the right to make 
changes as they become necessary. Any changes to 
our products may cause slight variations between the 
illustrations and explanations in this manual and the 
product you have purchased. The latest/current version 
of this manual is available on our website.

NOTE: This product is compliant with WEEE, RoHS, and 
REACH directives and requirements.

NOTE: This product meets IPX4 classification 
(IEC 60529).

NOTE: This product and its components are not made 
with natural rubber latex. Consult with the manufacturer 
regarding any after-market accessories.

Summary of Contents for TRU-BALANCE 3





























Reviews: