Quadratec Quadratop 12020-2000 Installation Manual Download | Manualshive

Page: 13 / 20

background image

13

STEP 4: INSTALLING ROPE ORGANIZER FOR RAFTERS (Side to Side)

A. Center one side of rope orginizer plate onto riser board and mark mounting hole location with pencil.

Drill two 5/32” mounting holes.

Rope Pulley Mounting Board

Rope Pulley Mounting Board

B. Assemble rope orginizer using plate and pulleys supplied in kit. Fasten to 2” x 6” riser board with with two

1/4” x 2 ½” lag bolts and 1/4” washers. Do not overtighten bolts. Rope orginizer pulleys will need to turn freely.

If overtightened hoist will not operate properly.

«
...
11
12
13
14
15
...
»

Summary of Contents for Quadratop 12020-2000





















Reviews:

No comments

Related manuals for Quadratop 12020-2000

PROFINET BNI PNT-508-055-P067

Brand: Balluff Pages: 84

Brand: MAHA Pages: 23

Brand: TITANCUT Pages: 44

Brand: SAF Pages: 59

Brand: ENTRYPASS Pages: 27

Brand: Fagor Pages: 68

WEIRO SUPERTIG315EX

Brand: ADN Pages: 13

Brand: Zepro Pages: 92

NC-MP-4A4B-12DLA/AL1403

Brand: Norgren Pages: 72

Brand: SMAR Pages: 47

Brand: ANDELI Pages: 23

Brand: ESAB Pages: 239

Brand: Tractel Pages: 42

DESKLINE DL18 IC

Brand: Linak Pages: 31

Brand: Cebora Pages: 8

Brand: National Instruments Pages: 28

OXeN X2-E-1.2-V

Brand: SIRE Pages: 19

AirGENIO SUPERIOR

Brand: 2VV Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands