background image

Page  2

7014-188L

September 24, 2015

1200-I Pellet Insert

and Welcome to the Quadra-Fire Family

!

Hearth & Home Technologies welcomes you to our tradition 
of excellence!  In choosing a Quadra-Fire appliance, you 
have our assurance of commitment to quality, durability, and 
performance.

This commitment begins with our research of the market, 
including ‘Voice of the Customer’ contacts, ensuring we 
make products that will satisfy your needs. Our Research 
and Development facility then employs the world’s most 
advanced technology to achieve the optimum operation of 

our stoves, inserts and fi replaces.  And yet we are old-fash-
ioned when it comes to craftsmanship.  Each unit is meticu-
lously fabricated and surfaces are hand-fi nished for lasting 
beauty and enjoyment.  Our pledge to quality is completed 
as each model undergoes a quality control inspection. 

   

From design, to fabrication, to shipping: 

We wish you and your family many years of enjoyment in 
the warmth and comfort of your hearth appliance.  Thank 
you for choosing Quadra-Fire.

 CLEARANCE TO COMBUSTIBLES LABEL LOCATED INSIDE HOPPER LID

SERIAL NUMBER & MANUFACTURE DATE LABEL LOCATED UNDER TOP ON INSIDE OF HOPPER BODY

NOTE:  Consult insurance carrier, local building inspector, fi re 
offi cials or authorities having jurisdiction over restrictions, 
installation inspection and permits.

 

HOT WHILE IN OPERATION DO NOT TOUCH.  KEEP CHILDREN, CLOTHING AND FURNITURE AWAY. 

CAUTION:

 

CONTACT MAY CAUSE SKIN BURNS. SEE NAMEPLATE AND INSTRUCTIONS.  Operate this unit with 

fuel hopper lid closed.  Failure to do so may result in emissions products' combustion from the hopper under certain 

conditions.  Maintain hopper seal in good condition.  Do not over fill the hopper.
 

CHAUD LORS DE L'OPÉRATION. NE PAS TOUCHER. GARDEZ LES ENFANTS ET LES VÊTEMENTS LOIN DE L'ESPACE 

ATTENTION:

 

DÉSIGNÉ DE L'INSTALLATION. LE CONTACT PEUT CAUSER DES BRÛLURES À LA PEAU.  VOIR L'ÉTIQUETTE ET LES 

INSTRUCTIONS.  Opérez cet appareil avec le couvercle de la trémie fermé. Le défaut de ne pas suivre les instructions peut résulter, sous certaines 

conditions, en une combustion des émissions des produits venant de la trémie. Ne pas remplir la trémie trop pleine.

Safety and clearance section located on inside of hopper lid

./

Serial Number section located under top on inside of hopper body.

La section se réfé dux distances et mescres de sécurité est située à l'intérieut du couvércle de la tré la bôitre à feu.   La section du numéro de série est située en dessous du couvercle à l'intérieur de la trémie.

Listed Solid Fuel Room Heater/Pellet Type Insert.  Also suitable for Mobile 

Home Installation.  This appliance has been tested and listed for use in 

Manufactured Homes in accordance with OAR 814-23-9000 through 

814-23-909.

R

CB1200MI-MBK

1445 North Highway, Colville, WA  99114

www.quadrafire.com

Tested to: ASTM E1509-95, UL127, ULC S628-93, ULC S610-M87, 

ULC/ORD C1482-M1990 Room Heating Pellet Burning Type, (UM) 

84-HUD FOR USE ONLY WITH PELLETIZED WOOD OR SHELLED 

FIELD CORN FUEL.

Input Rating: 46,400 Btu’s/hr

Electrical Rating:  115 VAC, 60 Hz, Start 4.1 Amps, Run 1.1 AMPS.

Route power cord away from unit. Do not route cord under or in front of 

appliance.

DANGER:  Risk of electrical shock.  Disconnect power supply before 

servicing.  Replace glass only with 5mm ceramic available from your 

dealer.

To start, set thermostat above room temperature, the stove will light 

automatically.  To shutdown, set thermostat to below room temperature.  

For further instruction refer to owner's manual.Keep viewing and ash 

removal doors tightly closed during operation.

MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS

Masonry or *Zero Clearance Minimum Clearances to Combustible

Maçonnene ou zéro distance foyer distances minimales à tout matériel combustible.

AS A BUILT-IN UNIT  WITH REAR SHROUD

7014-080G

7014-080G

1200-I PELLET INSERT

A  Louvers to combustible wall 

6” (152mm)

B  Insert top to mantel 

12” (305mm)

C  Front Facing 

3” (76mm)

D* Hearth Extension - Front 

6” (152mm)

E* Hearth Extension - Side 

8” (203mm)

A  Lucarne au mur combustible 

152mm

B  Dessus de l'insert à la tablette de cheminée  305mm

C Revêtement facial 

76mm

D* Protechion de sol - frontal 

152mm

E* Protechon ole sol - côté 

203mm

*Voir les notes sur la protechion ole sol ci-dessus.

DO NOT REMOVE THIS LABEL / NE PAS ENLEVER L'ÉTIQUETTE

SERIAL NO. / NUMÉRO DE SÉRIE

Report / Rapport

#061-S-13-2

DO NOT REMOVE THIS LABEL / NE PAS ENLEVER L'ÉTIQUETTE

Manufactured by:

Fabriqué par

:

0" (Omm) Clearance To Exposed Section and Face Trim

PRÉVENTION DES FEUX DE MAISON

Installez et utilisez en accord avec les instructions d'installation et d'opération du 
fabricant. Contactez le bureau de la construction ou le bureau des incendies au 
sujet des restrictions et des inspections d'installation dans votre voisinage. Ne 
pas obstruez l'espace en dessous de l'appareil.

AVIS - Pour Les Maisons Mobiles:

  Ne pas installer dans une chambre à 

coucher. Un tuyau extérieur de combustion d'air doit être installé et ne doit pas 
être obstrué lorsque l'appareil est en usage. La structure intégrale du plancher, 
du plafond et des murs de la maison mobile doit être maintenue intacte.
Référez vous aux instructions du fabricant et des codes locaux pour les 
précautions requises pour passer une cheminée à travers un mur ou un plafond 
combustibles, et les compensations maximums.
Inspectez et nettoyez la cheminée fréquemment. 

Ne pas connecter cet 

appareil à une cheminée servant un autre appareil.

Utilisez systèm de ventilation "L" ou "P" diamètre 76mm ou 102mm.

Testé à: ASTM E1509-95, UL127, ULC S628-93, ULC S610-M87, ULC/ORD C1482-M1990 Room 

Heating Pellet Burning Type, APFI, (UM) 84-HUD POUR USAGE AVEC LES BOULETTES DE BOIS 

OU DE COMBUSTIBLE DE MAIS ÉCOSSÉ DES CHAMPS.

Puissance de Rendement: 46,400 Btu's/hr

Puissance Électrique: 115 VAC, 60 Hz, Début 4.1 Amps, Courir 1.1 Amps, 

Éloignez le fil électrique de l'appareil. Ne pas faire passer le fil électrique au dessus ou en dessous 

de l'appareil.

DANGER: Il y a risque de décharge électrique.

  Déconnectez le fil électrique de la prise 

de contact avant le service.  Remplacez la vitre seulement avec une vitre céramique de 5 mm 

disponible chez votre fournisseur.  

Pour allumer, monter la température du thermostat au dessus de la température de la pièce, le poêle 

s'allumera automatiquement.  Pour éteindre, descendre la température du thermostat en dessous de 

la température de la pièce.  Pour des instructions supplémentaires, référez vous au manuel du 

propriétaire.  Gardez la porte d'ouverture et la porte des cendres fermées hermétiquement durant 

l'opération.

Appareil de chauffage inséré de combustible solide/de type de boulettes.  Accepté dans 

l'installation dans les maisons mobiles.  Cet appareil a été testé et enregistré pour l'usage 

dans les Maisons Mobiles en accord avec OAR 814-23-9000 jusqu'à 814-23-909.

B

D

C

E

B

C

A

*Zero clearance installation requires 
non-combustible hearth material with 
an R value of 3.0 or more (“k” value of 
.58) or a 1” (25mm) air space between 
insert base and hearth. Floor Protection 
Part 811-0730 is available from your 
dealer for the section under the insert 
body only.

HEARTH PROTECTION

A  Top of Inside Shroud

B  Sides of Inside Shroud
C  Back of Inside Shroud)

D  

Vent Pipe to Combustible

E  From Panel Edge

0" (0mm)
3" (76mm)
0" (0mm)
0" (0mm)
2-1/2" (64mm)
3" (76mm)
0" (0mm)

Rear Vent
Top Vent
Top or Rear
Rear Vent
Top Vent )
Rear Vent

QUADRA-FIRE

SIDE W

A

LL

A

B

C

D

E

MANTEL

007071

MADE IN CHINA / FAIT AUX CHINE

O-T L

Tested and 

Listed by

Portland

Oregon USA

OMNI-Test Laboratories, Inc.

C

US

PREVENT HOUSE FIRES

Install and use only in accordance with manufacturer's installation and 

operating instructions.  Contact local building or fire officials about 

restrictions and inspection in your area.

WARNING - FOR MOBILE HOMES:  Do not install appliance in a sleeping 

room.  An outside combustion air inlet must be provided.  The structural 

integrity of the mobile home floor, ceiling and walls must be maintained.

Refer to manufacturer's instructions and local codes for precautions 

required for passing chimney through a combustible wall or ceiling.  

Inspect and clean vent system frequently in accordance with 

manufacturer's instructions.

DO NOT CONNECT THIS UNIT TO A CHIMNEY SERVING 
ANOTHER APPLIANCE.

Use a 3" or 4" diameter type "L" or "PL" venting system.

2015 2016 2017 Jan

Feb

Mar

Apr

May

Jun

Jul

Aug

Sep

Oct

Nov

Dec

*See hearth protection note above

U.S. ENVIRONMENTAL PROTECTION AGENCY

     

OMNI Test Laboratories, Inc., Portland, Or  Report/Rapport 061-S-13-2

Certified to comply with 2015 particulate emissions standards at 1.1 g/hr EPA method 28 and 5G. Not approved for sale after May 15, 2020

THIS WOOD HEATER NEEDS PERIODIC INSPECTION AND REPAIR FOR PROPER OPERATION. CONSULT THE OWNER’S MANUAL FOR FURTHER INFORMATION. IT IS AGAINST 

FEDERAL REGULATIONS TO OPERATE THIS WOOD HEATER IN A MANNER INCONSISTENT WITH THE OPERATING INSTRUCTIONS IN THE OWNER’S MANUAL.

Summary of Contents for PELLET INSERT CB1200MI-MBK

























































Reviews: