background image

AN-X4-ABRIO-HMI

 Page

 39 

 

 

Administration Menu 

The 

Administration

 menu contains items used to configure, control and update the AN-X. 

AN-X IP Configuration 

Use 

Administration

/

AN-X IP Configuration

 to set the AN-X Ethernet properties. 

 

 

The top of the screen shows the serial number and MAC Address of the AN-X4 being configured. 

To configure Ethernet on the AN-X, check DHCP, Static or Factory. 

DHCP 

If the AN-X4 finds a DHCP server on the network, it obtains an IP address and other network 
parameters (netmask and default gateway) from the DHCP server. 

To find the address assigned, look at the DHCP server or use a network tool that displays devices on 
the network. 

If the AN-X has been configured for DHCP and it does not find a DHCP server, it waits forever for a 
DHCP server and repeatedly flashes the MS LED yellow 2 times followed by a pause.  The NS LED 
will be solid red. 

Static IP Address 

If you select static IP address, enter: 

 

the IP address for the AN-X. 

 

the netmask for the AN-X 

 

the default gateway for your network.   

Summary of Contents for AN-X4-ABRIO-HMI

















































Reviews: