QSI 600 Series User Manual Download | Manualshive

Page: 26 / 61

background image

26

Camera soft error state indication

Flash Red: 1

Flash Yellow:1

The camera is over-temperature. Camera has exceeded the 40°C maximum recommended

operating temperature for the internal electronics and enclosure. This sequence will repeat

every four seconds as long as the camera remains “over- temperature”.

Flash Red: 1

Flash Yellow: 2

The CCD is under-temperature. The CCD has exceeded the -40°C minimum recommended

operating temperature. This sequence will repeat every four seconds as long as the CCD

remains “under-temperature”.

Flash Red: 1

Flash Yellow: 3

The camera DC supply voltage is below the 11V minimum recommended operating level. This

sequence will repeat every four seconds until the supply voltage is raised above this threshold.

Flash Red: 1

Flash Yellow: 4

The camera DC supply voltage is above the 14V maximum recommended operating level. This

sequence will repeat every four seconds until the supply voltage is lowered below this threshold.

Flash Red: 1

Flash Yellow: 5

The filter wheel has encountered a problem and is no longer operational. The camera will still

function, but will no longer attempt to move the filter wheel. The filter wheel may be in any

position. Power to the camera must be turned off and on to reinitialize the filter wheel.

Flash Red: 1

Flash Yellow: 6

The shutter has encountered a problem and is no longer operational. The camera will still

function, but will no longer attempt to operate the shutter. The shutter may be in any state.

Power to the camera must be turned off and on to reinitialize the shutter.

«
...
24
25
26
27
28
...
»

Summary of Contents for 600 Series






























































Reviews:

No comments

Related manuals for 600 Series

Brand: OCO Pages: 11

Brand: D-Link Pages: 8

SMARTCAM SNH-V6414BN

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 96

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 1

Brand: Veeder-Root Pages: 3

Brand: Fenton Pages: 56

Brand: Zadako Pages: 15

Brand: jablotron Pages: 2

Brand: jablotron Pages: 17

Brand: Dahua Pages: 16

Brand: Doberman Pages: 6

Brand: V-TAC Pages: 9

Brand: unii Pages: 2

Brand: ADT Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands