background image

2

Specifications

Table 1.

ST-590 Specifications

Specification

*

ST-590

ST-590SS

Part Number (P/N)

50690

50691

Fluorescent Polymer
Range

0.0–20.0 ppm

Fluorescent Polymer
Accuracy

±

0.1 ppm

Excitation Wavelength

410 nm

Emission Wavelength

450 nm

Wavelength Accuracy

±

1 nm

Calibration

Two-point calibration against standard solution

Outputs

4–20mA Analog Output,

RS-485 Digital Output with Modbus protocol

Installation

Custom tee assembly (P/N: ST-001)

with 3/4” FNPT socket & threaded

ports

3/4” FNPT threaded ports

Cable Length

5 ft with IP67 connectors & 2 ft flying lead with IP67 adapter

Power Supply

22–26 VDC, 1 W

Dimension (L

×

Dia)

6.8

×

1.44 inch (172.7

×

36.6 mm)

See Figure 3

Weight

0.37 lbs (170 g)

2.5 lbs (1148 g)

Material

CPVC

304 Stainless Steel

Operational
Temperature

40–104 °F (4–40 °C)

Storage Temperature

20–140 °F (-7–60 °C)

Pressure

Up to 100 psi (0.7 MPa)

Up to 290 psi (2.0 MPa)

Enclosure Rating

IP67

Regulation

CE

*

With Pyxis’s continuous improvement policy, these specifications are subject to change without notice.

The fluorescent polymer concentration scale is based on the polymer containing 0.25 mole % fluorescent
monomer. Typical polymer specifications are attached below but may vary by producer.

3

Unpacking Instrument

Remove the instrument and accessories from the shipping container and inspect each item for any damage
that may have occurred during shipping. Verify that all accessory items are included. If any item is missing
or damaged, please contact Pyxis Lab Customer Service at

[email protected]

.

3.1

Standard Accessories

• Tee Assembly 3/4” NPT (1x Tee, O-ring, and Nut)

P/N: ST-001

*

NOTE

*

ST-001 is not included for ST-590SS

• 7-Pin Female Adapter/Flying Leads Cable (2 ft)

P/N: MA-1100

• User Manual available online at

https://pyxis-lab.com/support/

ST-590 User Manual

[email protected]

| +1 (866) 203-8397

3

Summary of Contents for 50690






















Reviews: