background image

1

INTRODUCTION

The Octagon II is a full featured intruder alarm control panel, based around a  microprocessor with 8 fully programmable

zones and 2 dedicated '24-hour' zones (Personal Attack alarm and a System-Tamper alarm.). It is operated via a 16 - key

remote keypad and has an arrangement of 3 LEDs and LED display to show the status of the system.

All features are fully programmable and there are three levels of access to the system :

Master User (user 1)

factory default (1 2 3 4)

Limited User (user 2)

factory default (5 6 7 8)

(if  enabled)

Cleaner  Code

factory default (7 8 9 0)

(if  enabled)

Engineer

factory default (9 9 9 9)

The Master User  code  gives access to all settings and unsetting facilities and also allows the changing of code numbers

and testing of the system.

The Limited User code gives access to the basic functions needed for everyday setting and unsetting the system.

The Cleaner code can only set and unset the panel in programmed areas.

The Engineer code gives total access to the system programming during day mode.

2

SAFETY

Mains: The mains supply to the control panel is connected via a 3 way terminal block.

**This equipment is not suitable for location in bathrooms or damp conditions. Always remove / isolate mains before

carrying out work on the panel. The mains installation should be carried out in accordance with current IEE regulations

by a technically competent person**.

3

ACCESS LEVELS

Master User 

(user 1) enables:

Limited User

 (user 2) enables:

1. Chime programming.

1. Panel setting and unsetting with a unique pass code.

2. Alteration of all access codes except engineers.

2. Changing user code 2.

3. Test mode.

3. Omitting zones.

4. All user code 2 facilities.

4. Setting and unsetting of the door chime facility.

Cleaner level

 enables:

Engineer level 

enables:

1. Panel setting.

1. Changing engineers code.

2. Unset panel except programmed cleaner zones.

2. All system programming.

3. Panel setting and unsetting providing panel is in daY

                                                                                                               mode.

4

FEATURES

-  2 User-Level Codes, cleaner code and engineers code, all programmable .

-  Fast-set facility.

-  8 Programmable alarm zones.

-  8 Zone Tampers.

-  4 Full set / Part set configurations.

-  Personal Attack alarm zone.

-  16 key backlit keypad.

-  3 LEDs and LED display on RKP for immediate indication of  panel status.

-  8 LEDs on the new RKP II.

-  Walk Test facility.

-  System Test Function.

-  Extension speaker volume control with alarm override.

-  Separate Bell and Strobe outputs.

-  Zone omit facility on exit.

-  Part sets programmable as silent, time or instant.

-  Digital Communicator outputs.

-  Optional communicator delay / activation polarity.

-  Customer / engineer reset.

-  Two individual keyswitch inputs.

-  Soak zones, Fire zones and 24 Hour zones.

-  Non omitable zones.

-  Up to four remote keypads.

-  Additional zone on each keypad.

-  Duress code.

-  100 event memory.

-  Push to set input.

-  Final door exit option.

                        RDOC298D/C  Issue 1

5

All manuals and user guides at all-guides.com

Summary of Contents for OCTAGON II


































Reviews: