EN
60
Operating Manual: XSD200 - Smoke Alarm Device with Radio Link
Operating Manual: XSD200 - Smoke Alarm Device with Radio Link
EN
61
EN
EN
5.1 Adhesive mounting
The magnet carrier can be mounted us-
ing adhesive assembly as follows:
•
Easy to maintain and removable ac-
cording to EN 14604:2005/AC:2008 or
•
maintenance-unfriendly but theft-
proof according to
EN 14604:2005/AC:2008
and vfdb 14/01 (Q)
Adhesive mounting according to
EN 14604:2005/AC:2008
When performing this type of installation,
proceed as follows:
(1) Remove magnet carrier from the
device. (Remove the splint from the
activation button only after that.)
f
To do this, tilt the magnet carrier.
22
Betriebsanleitung: RWM200 – Rauchwarnmelder
DE
5 Montage
D a s G e r ä t w i r d v o n e i n e m
Magnetträger am Montageort gehal-
ten. Der Magnetträger kann durch
Kleben oder Bohren montiert wer-
den. Um Verletzungen durch unsachge-
mäße Montage vorzubeugen, sind die
Hinweise in dieser Anleitung zwingend
anzuwenden sowie die allgemeinen
Sicherheitsvorschriften zu beachten.
VORSICHT
Mögliche Sachschäden!
Durch das Verwenden eines anderen
Befestigungsmittels (nicht mitgeliefert)
oder durch falsche Voraussetzungen
am Montageort kann das Gerät
herunterfallen.
f
Verwenden Sie ausschließlich das
mitgelieferte Befestigungsmaterial
(Klebepad oder Schrauben/Dübel).
f
Stellen Sie sicher, dass der Mon-
tageort ausreichend tragfähig, fest,
trocken, frei von Fett, Staub und
losen Anstrichen etc. ist.
B e a c h t e n S i e , d a s s d e r
Magnetträger nur von einer Seite
stark magnetisch anziehend wirkt.
5.1 Klebemontage
Den Magnetträger können Sie wie folgt
mittels Klebemontage montieren:
•
wartungsfreundlich und abnehmbar
nach EN 14604:2005/AC:2008
•
oder wartungsunfreundlich aber
diebstahlsicher nach EN 14604:2005/
AC:2008 und vfdb 14/01 (Q)
Klebemontage nach EN
Klebemontage nach EN
14604:2005/AC:2008
14604:2005/AC:2008
Gehen Sie bei dieser Montageart wie
folgt vor:
(1)
Magnetträger vom Gerät entfernen
f
dazu Magnetträger ankippen
(2) Remove the protective film from the
adhesive pad on the magnet carrier.
(3) Press the magnet carrier firmly for
about 10 seconds at the mounting
position.
(4) Activate the device and set it up.
f
Observe chapter 6 “Initial activation
and setting up“ on page 63.
(5) Position the device on the magnet
carrier.
5
The device is mounted on the
magnet carrier.
The ultimate strength of the adhe-
sive bond is achieved after about
72 hours.
Adhesive mounting according to EN
14604:2005/AC:2008 and vfdb 14/01
(Q)
To establish a permanent connection
between the device and magnet carrier
(e.g., as theft protection), you can addi-
tionally mount the device with the sup-
plied adhesive film on the magnet carrier.
CAUTION
Possible property damage!
Mounting the device in accordance
with vfdb 14/01 (Q) establishes a
permanent connection between
magnet carrier and the device. Thus,
a subsequent removal of the device
is prevented. The start-up and set up
of the device are no longer possible.
If the device is disassembled, it can
cause damage to the device and the
mounting surface.
f
Use the additional adhesive film
only to prevent theft.
f
Activate the device and set it up
before attaching the additional
adhesive film.
When performing this type of installation,
proceed as follows:
(1) Mount the magnet carrier.
f
Observe chapter “Adhesive mounting
according to EN 14604:2005/AC:2008“ on
page 60.
(2) Activate the device and set it up.
f
Observe chapter 6 “Initial activation
and setting up“ on page 63.
(3) Attach the additional adhesive film
to the magnet carrier sheet plate on
the device.
f
Remove the protective film from
one side of the adhesive film.
f
Place the adhesive film on the mag-
net carrier sheet plate on the device
and press it on.
f
Remove the protective film on the
other side.
(4) Place the device on the magnet
carrier and press it on.
5
The device is mounted on the mag-
net carrier.
