background image

 

Pylon Technologies Co., Ltd. Confidential Proprietary

5

 

Normal

Shut Down

Off

Off

Off

Off

Off

Off

All off

Standby

Normal

Flash1

Off

Off

Off

Off

Off

Indicates Standby

Alarm

Off

Flash3

Off

Off

Off

Off

PACK Low Voltage

Directive

Charge

Normal

Light

Off

Based on capacity

the right side

indicator LED

flashes (flash 2),

others lighting

Alarm

Light

Flash3

Protection

Off

Light

Off

Off

Off

Off

Stop charging, ALM

lighting

Discharge

Normal

Flash3

Flash3

Based on capacity

Alarm

Flash3

Flash3

Indicate based on

capacity

Protection

Off

Light

Off

Off

Off

Off

Stop discharging,

ALM lighting

Note: The flashing instructions, flash light 1 - 0.25s / off 3.75 seconds; flash 2 - 0.5s light / 0.5s

off; flash 3 - 0.5s light / 1.5s off

2.2

Battery Management System

BMS

2.2.1 Voltage Protection

Low Voltage Protection in Discharge:

When discharging, the protection starts if any one of the single cells has lower

voltage than the setting value and the power supply stop. When voltages of all

single cells return to the normal, protection removed.

Protection parameters see entry 1 of "Table 2-5 Protection Parameters".

High Voltage Protection in Charge

When charging, the system stops charging when the total voltage of the

battery or any one cell over the voltage value. When total voltage and cell

voltage are restored to the normal, protection removed.

Protection parameters see entry 2,3 of "Table 2-5 Protection Parameters".

Extra 2000 Lithium Iron Phosphate Battery Backup Manual

Summary of Contents for Extra 2000




























Reviews: