manualshive.com logo in svg

PumpSaver 777, Installation Instructions Manual

Share
Download
PumpSaver 777 Installation Instructions Manual Download Page 8

Trip Class

Application Description

5

Small fractional horsepower motors where acceleration times are almost
instantaneous or where extremely quick trip times are required.

10

(Fast Trip) Hermetic refrigerant motors, compressors, submersible pumps and
general-purpose motors that reach rated speed in less than 4 seconds.

15 

Specialized 

applications

20

(Standard Trip) Most NEMA-rated, general-purpose motors will be protected by
this setting.

30

(Slow Trip) Motors with long acceleration times (>10 seconds) or high inertia
loads.

J prefix

Programming any of the trip classes with the J Prefix will enable jam protection.
This additional protection is enabled 1 minute after the motor starts and
provides a 2-second trip time for motors exceeding 400% of the OC setting,
regardless  of trip class.

Table 4. Trip Class Descriptions

Figure 4. Overload Trip Curves

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Summary of Contents for 777
















Reviews:

No comments

Brands by name

Popular brands

Load more brands