manualshive.com logo in svg

PumpSaver 777, Installation Instructions Manual

Share
Download
PumpSaver 777 Installation Instructions Manual Download Page 13

Mechanical

     Dimensions

3.0"H x 5.1"D x 3.6"W

     Terminal Torque

7 in.-lbs.

     Enclosure Material

Polycarbonate

     Weight

1.2 lbs.

     Maximum Conductor Size

0.65" with insulation

Environmental

     Temperature Range

Ambient Operating: -40° to 70°C (-40° to 158°F)
Ambient Storage: -40° to 80° C (-40° to 176°F)

     Pollution Degree

3

     Class of Protection

IP20, NEMA 1

     Relative Humidity

10-95%, non-condensing per IEC 68-2-3

Programmable Operating Points

Range

     MULT- # of Conductors or CT Ratio (XXX:5)  

1–10 Conductors or 100–800 Ratio

     HP

.1–50

 FLA

0, (20–207A) ÷ MULT
or 0, 80–140% of CT primary (992 max.)

     EFF/PF

E00–E99,  P00–P99

      OC- Overcurrent Threshold

(20–100A) ÷ MULT
or 80–140% of CT Primary (992 max.)

     TC- Overcurrent Trip Class *

5, J5, 10, J10, 15, J15, 20, J20, 30, J30

      CUB- Current Unbalance Threshold

2–25% or 999%

     PWS- Power Setpoint Range

1 = 0.01–0.99 kW

     (for LPR and HPR setpoints)

2 = 1.00–9.95 kW
3 = 10.0–99.5 kW

NOTE:   LPR can be set to “0” and

4 = 100–650 kW

HPR to “off" to disable these features

5 = 0.01–1.30 hp
6 = 1.34–13.3 hp
7 = 13.4–133 hp
8 = 134–871 hp

     LPR- Low Power

Range determined by PWS

     HPR- High Power

Range determined by PWS

     RD1- Rapid Cycle Timer

0, 2–500 Seconds

     RD2- Restart Delay After All Faults Except

Underload (motor cool-down timer)

0, 2–500 Minutes

     RD3- Restart Delay After Underload

(low-flow recovery timer)

0, 2–500 Seconds, A (Automatic)

     COMM- RS485 Address

A01–A99 or OP1 for 4–20mA output

     FS- Full Scale
            (required when using 4-20 mA module)

Full Scale Range (determined by PWS)

PWS =1

.4–1.39 kW

2

1.4–14.0 kW

3

14.0–138 kW

4

140–654 kW

5

.53–1.86 hp

6

1.87–18.7 hp

7

18.7–185 hp

8

187–877 hp

NOTES:

SymCom's Power Monitor/Motor Protection Relay can be programmed prior to installation

by applying 120VAC between the L1 and L2 terminals (except 575 Volt model). Power applied must
be 110VAC or greater.

* If a J prefix is displayed in trip class setting, jam protection is enabled.
** on a well-balanced system within recommended current range

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Summary of Contents for 777
















Reviews:

No comments

Brands by name

Popular brands

Load more brands