background image

PROGRAMMABLE PARAMETERS

The following settings MUST be programmed by the user in order to provide proper protection for
the application. All parameters are actual values except for CUB, which is programmed as a

percentage. The programmable range for each parameter can be found on the specifications table

on page 13. See page 9 for a

programming  example.

MULT

-   MULT (multiplier) is

determined by the current the

unit will be monitoring and can

be found in Table 1. This

allows the unit to display the

correct current. Changing this

setting will also change the
OC, and FLA setpoints

.

HP -

HP (horsepower) should be
set according to the hp rating on the nameplate of the motor. This setting is required for

proper operation of the Model 777-AccuPower. The unit can be set from .10-50hp; dial in

the closest available setting (select 50 if the motor is greater than 50hp.)

FLA

FLA (full load amps) is the current drawn while the motor is running normally and

can be read from the nameplate. EFF is automatically calculated and set when HP and

FLA are programmed, so if FLA is not entered, EFF must be programmed manually.

EFF/PF

-   EFF/PF (efficiency/power factor) can be found on the motor’s nameplate or

manufacturer’s specification sheet. If the efficiency rating is available, it is best to enter it;

and FLA should be set to 0. If the efficiency is not available, it will automatically be

calculated and set according to the HP and FLA settings. Power factor can also be
entered according to the motor’s nameplate or manufacturer’s specification sheet, and

should be entered if available.

OC

-  

OC (overcurrent) is usually set at the service factor amperage (typically 100-115% of

motor FLA) of the motor, which is determined by the motor manufacturer. If any one leg of

current exceeds the OC setting, the unit will follow its overload trip curve (see Figure 4).

TC

-  

TC (trip class) is the parameter used to determine when the unit will trip when an overload

condition is detected. For standard motors, the TC is typically set at 20. The motor

manufacturer should be contacted for exact TC settings. Table 4 and Figure 4 show the

range of TC settings and trip times.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Summary of Contents for 777
















Reviews: