PT AMC123 User Manual Download Page 51

Page: 51 / 104

Installing Drivers

d. Arrow up or down to highlight the USB device. Press

<Enter>

USB

appears at the top of the

Boot

Device Priority

list.

e. Press <Esc> to exit to the main menu.

f. Right arrow to select the

Exit

menu item.

Save Changes

and

Exit

is highlighted.

g. Press

<Enter>

is highlighted.

6. Press

<Enter>

to exit the BIOS setup utility.

Note:

Windows XP and Red Hat Enterprise Linux AS 4 Update 3 (AMD64/Intel EM64T) have

been validated for this installation.

PXE

PXE operation is only supported on Ethernet Port 0 to the AMC edge connector.

Operating Systems Supported

The AMC123 supports the following operating systems:

•

Microsoft Windows XP Embedded

•

Microsoft Windows XP, SP2 or later

•

Microsoft Windows Vista has been installed, but is not directly supported by Intel

•

NexusWare Core CGL OS and Development Environment has been installed successfully

•

Red Hat Enterprise Linux AS 5

The following operating systems may also be installed on the AMC123:

•

Solaris 10

•

CentOS 5.2

•

Wind River Linux 2.0

•

Wind River VxWorks 6.6

•

FreeBSD 6.3

Installing Drivers

Windows XP Embedded Drivers

The following

Getting Started Guide

documents the instructions to obtain, build (if necessary),

install, and execute the Windows XP Embedded drivers for the Intel EP80579 Integrated
Processor.

•

Intel® EP80579 Software Drivers for Embedded Applications on Microsoft Windows XP Embedded
Getting Started Guide

This document and the Windows XP Embedded drivers can be found on Intel’s Web site and
the PTI beta page for the AMC123:

•

http://www.intel.com/design/intarch/ep80579/index.htm

•

http://pt.com/page/beta/amc123

(password required)

Summary of Contents for AMC123









































































































Search results

Summary of Contents for AMC123

Reviews:

Related manuals for AMC123

Brands by name

Popular brands

PT AMC123, User Manual

Search results

Summary of Contents for AMC123

Reviews:

Related manuals for AMC123

Brands by name

Popular brands