PT AMC123 User Manual Download Page 33

Page: 33 / 104

AMC123 Functional Blocks

Extraction Sequence

Off

Module is in normal operational state. User may initiate deactivation by
pulling out the module handle to open the hot-swap switch, sending a
request via the MMC to the carrier for a hot-swap extraction.

Blue short blink

Module handle open. Module is waiting to be deactivated. Not safe to extract
module.

Blue on

Module is quiesced, module payload power is disabled. Safe to extract
module.

Board Diagnostic LEDs

Several surface mount (SMT) LEDs are located on the PCB, which are for debug/status. These
SMT LEDs are described in

Table 2-2, “Board Diagnostic LEDs,”

below.

Rear Panel I/O

The AMC123 transitions the following I/O signals through the AMC card edge connector to the
carrier:

•

SerDes Gigabit Ethernet (Port 0 and Port 1)

•

SATA (Port 2 and Port 3)

•

x8 PCI Express (Ports 4-11) or two x4 PCI Express (Ports 4-7 and Ports 8-11)

•

USB (Port 13)

•

IPMI

•

Reset

•

Power and Ground

See the topic

“AdvancedMC Card Edge Connector (P1),” on page 80

, for more information.

Table 2-2:

Board Diagnostic LEDs

Number

Name

Indicates

SATA Disk Module PHY Ready LED

On = Ready

SATA Disk Module Activity LED

Blink = Activity

SATA Hard Activity Port Activity LED

On = SATA access
Off = No SATA access

System Reset LED

On = System in reset

System PWROK LED

On = System power is OK
Off = Power not OK

Ethernet Port 0 Link LED to AMC edge connector

On = Link
Off = No Link

Ethernet Port 0 Transmit LED

On = Linked
Blink = Activity
Off = Not linked

User LED on front panel

See

“User LED,” on page 32

Summary of Contents for AMC123









































































































Search results

Summary of Contents for AMC123

Reviews:

Related manuals for AMC123

Brands by name

Popular brands

PT AMC123, User Manual

Search results

Summary of Contents for AMC123

Reviews:

Related manuals for AMC123

Brands by name

Popular brands