background image

Promix-RDS.01

 

 

7

 

 

The warranted operation period of the products is 12 months from the date of 

sale but not longer than 18 months from the day of acceptance by the 

manufacturer’s QCD.  

The warranty does not cover the batteries included in the set. 

Faulty products are accepted for repair only complete, with the compulsory 

preservation of the factory labels on the body of the products.

 

To improve the quality of the product, the manufacturer reserves the right to 
make changes in the design of products without prior notice.

 

12.

 

WARRANTY LIABILITIES

 

The manufacturer, ETC PROMIX LLC, warrants conformity of the products to requirements of 

current technical specifications provided that the transportation, storage, installation and operation 
rules established in this Manual are followed. 

Within the period of warranty, ETC PROMIX LLC undertakes to eliminate defects of the system 

components, caused by the Manufacturer's  fault,  or to replace defective components and units 
free of charge. Costs of delivery to and from the place of repair shall be borne by the Buyer. 

Warranty liabilities do not cover any defects and damages caused by: 

  Improper maintenance by the Buyer; 

  Use of the products under conditions that do not comply with the operation requirements; 

  Mechanical damages or disassembly of the products by the Buyer; 

  Non-observance of the transportation and storage rules. 

After the expiration of the warranty service period, the manufacturer provides post-warranty 

service of the product on a contractual basis. 

13.

 

ACCEPTANCE AND PACKING CERTIFICATE

 

The remote control system 

PROMIX-RDS.01

 in quantity of ___ pieces (1 peace by default) bearing the 

manufacturing date and QCD mark on the body is manufactured and accepted according to 

ПШБА.

464415.1

01  ТУ,  meets  the  obligatory 

requirements of state standards and current technical 

documentation, is recognized fit for operation and packed by ETC PROMIX LLC. 

 
 
 
 
 

Engineering and Technical Center PROMIX LLC 
Russia, 214030, Smolensk, Krasninskoye shosse, 35, letter A

 

Tel. (4812) 619-330 

www.promix-center.com

  

www.facebook.com/Promixcenter

 

[email protected]

 

 

 

Summary of Contents for RDS.01








Reviews: