background image

16-07-2019 

 

OPERATING MANUAL  

Technical description. Installation manual. Certificate. 

ПШБА.464415.101 РЭ

 

Check the completeness of the product upon purchase! The manufacturer will 

not accept any further claims for completeness.

 

 

 

 
 
 

 

 
 
 

 

1.

 

PURPOSE

 

Remote control system Promix-RDS is designed for radio remote control of various actuators 

(electromagnetic, electromechanical locks, latches; turnstiles, etc.). 

The system includes: actuator, power supply unit, receiver, controller unit, remote controls. The 

power supply unit, receiver, and controller unit are designed as a single unit (controller

 

Promix-

CR.RX.03

,  hereinafter –  the controller). The receiver of the controller receives control signals of 

remote controls

 

Promix-CR.TX.01

The power supply unit of the controller is used to control the 

connected actuators. 

2.

 

DELIVERY SET

 

Controller Promix-CR.RX.03 

 

1 pc. 

Remote control Promix-CR.TX.01 with a battery

 

2 pcs.

 

Operating manual  

1 pc.

 

3.

 

CLIMATIC OPERATING CONDITIONS OF THE 

CONTROLLER

 

  resistance to climatic factors according to GOST15150-

69:УХЛ4;

 

  ambient air temperature: from -

30 to +50 °С;

 

 

relative  air  humidity  not  more  than  80%  at  +25  °С  and  lower  temperatures  without 

condensation and frost formation. 

 

 

REMOTE CONTROL SYSTEM

 

Promix-RDS.01

 

Summary of Contents for RDS.01








Reviews: