background image

C

APPENDIX

C

other item. You assume full responsibility for selecting products and for
ensuring that the products selected are compatible and appropriate for use
with other goods with which they will be used.

Promise DOES NOT WARRANT that any product is free from errors or
that it will interface without any problems with your computer system. It is
your responsibility to back up your computer or otherwise save important
data before installing any product and to continue to back-up your important
data regularly.

Promise’s  sole  responsibility with respect to any product is, at Promise’s
election, to (a) replace the product with a conforming unit of the same or a
superior product; (b) repair the product; or (c) recover the product and
refund the purchase price for the product, less the amount of any damage
and compensation for any use of the product. Promise shall not be liable for
the cost of procuring substitute goods, or services, lost profits, unrealized
savings,  equipment  damage, costs of recovering, reprogramming, or
reproducing any programs or data stored in or used with the  products, or
for any other general, special, consequential, indirect, incidental, or punitive
damages, whether in contract, tort, or otherwise, notwithstanding the failure
of the essential purpose of the foregoing remedy and regardless of whether
Promise has been advised of the possibility of such damages. Promise is not
an  insurer. If you desire insurance against such damage, you must obtain
such insurance from another party.

Some states do not allow the exclusion or limitation of incidental or
consequential damages for consumer product so the above limitation or
exclusions may not apply to you.

This warranty gives specific legal rights, and you may also have other rights
which vary from state to state. This limited warranty is governed by the
laws of the state of California.

C-2

Summary of Contents for FastTRAK66










































































Reviews: