manualshive.com logo in svg

ProMinent gamma/ L, Operating Instructions Manual, Page: 45 / 81

Share
Download
ProMinent gamma/ L Operating Instructions Manual Download Page 45

Pr

o

Minent

®

Page 35

Troubleshooting / Decommissioning and Disposal

Fault Signals

Yellow LED display is lit

Cause

Liquid level in chemical storage tank has reached “liquid level low, stage 1”

Remedy

S

Fill chemical storage tank

Yellow LED Display is lit and “calib” flashes

Cause

The pump is calibrated and the stroke length deviates by more than ± 10% from the value at the
time of calibration.

Remedy

S

Reset the stroke length or calibrate the pump again to the desired stroke length

13

 Decommissioning and Disposal

Decommissioning

WARNING

•

When decommissioning the gamma/ L the housing and, in particular, the li-
quid end must be thoroughly cleaned to remove chemicals and dirt!

•

Always take suitable precautions when using hazardous chemicals!

•

Ensure that the equipment is de-pressurised!

S

Disconnect the gamma/ L from the power supply

S

Empty the liquid end by turning the gamma/ L upside down and allow the feed chemical to
pour out

S

Rinse the liquid end with a suitable material, thoroughly rinse the liquid end after use with
hazardous materials!

If decommissioning is only temporary, maintain the correct storage conditions:

Storage temperature:

-10 to +50 °C

Air humidity:

< 92 % relative humidity

Disposal

TAKE CARE

Electronic waste is classified as special waste!

Please observe all locally applicable directives!

Summary of Contents for gamma/ L


















































































Reviews:

No comments