Promax OL-612 User Manual Download Page 69

Page: 69 / 128

Page

October 2014

3.5.1

How to Implement the Auxiliary System Function Setting

Press the

UNTILITY

button and the menu is displayed in the screen as Fig. 60.

Figure 60.

Function menu.

Function Menu

Setting

Description

System Status

Display the system function menu.

Recall Factory

Call out the factory settings.

Do Self Cal

Carry out the self-calibration procedure.

Language

Spanish

English

…

Choose the display language of the

operating system.

►

Carry out a Self-Calibration

We have a built-in Self-Calibration procedure, by performing a Self-Calibration

would help to maintain the accuracy of your oscilloscope under ambient

temperature. It is recommended to carry a self-Calibration if the change of the

ambient temperature is up to or exceeds 5

NOTE: Disconnect all inputs before carrying out a self-calibration. Fail

to do so may cause damage to your oscilloscope.

Summary of Contents for OL-612

































































































































Search results

Summary of Contents for OL-612

Reviews:

Brands by name

Popular brands

Promax OL-612, User Manual

Search results

Summary of Contents for OL-612

Reviews:

Brands by name

Popular brands