Promax OL-612 User Manual Download Page 103

Page: 103 / 128

Page

October 2014

Storage menu instruction as below:

Function

Setting

Instruction

Memory

SEL

Waveform

Setups

Waveform for storage or recall.
Setups for storage or recall.

Memory

Waveform0

Waveform3

Setups 0

Setups 9

Storage 4 groups of waveform.
Storage 10 groups of setups.

Save

Save current waveform/setting in

designated No.

Recall

Recall waveform/ setups in designated No.

For example, to set "

WAVE 0

" in memory ID to save current waveform and

"setting 0" to save current setting. Follow up below steps:

Press "

C(SAVE/REL)

" after data acquisition finished and storage

menu appears.

Press "

" till storage display as "

Waveform

Press "

" till memory ID. Display as "

Waveform 0

Press "

" to save current display waveform. Info window will show

Waveform saving

" then show as "

Waveform saved successfully

when storage finished.

Press "

" till memory SEL as "

Setups

Press "

" till memory ID. display as "

Setups 0

Press "

" to save current various settings. Info window show

Setting saved successfully

Press "

" to recall the memory waveform or settings (refer to Fig.

95).

Figure 95.

Waveform saving.

Summary of Contents for OL-612

































































































































Search results

Summary of Contents for OL-612

Reviews:

Brands by name

Popular brands

Promax OL-612, User Manual

Search results

Summary of Contents for OL-612

Reviews:

Brands by name

Popular brands